Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
PRECAUTIONS
• If the suction power of the vacuum cleaner de-
creases rapidly while cleaning, switch it off imme-
diately, remove the power plug from the socket and
check the telescopic pipe and the flexible hose for
obstruction. Remove the obstruction and only then
you can continue cleaning.
• Do not use the vacuum cleaner near hot surfaces,
ashtrays and in the places where inflammable liq-
uids are stored.
ASSEMBLING THE VACUUM CLEANER
After unit transportation or storage at low
temperature it is necessary to keep it for at least
two hours at room temperature before switching
on.
• Unpack the vacuum cleaner completely and check it
for damages. In case of any damages do not switch
the vacuum cleaner on or use it.
• Before switching the vacuum cleaner on for the first
time make sure that your home mains voltage cor-
responds to the vacuum cleaner operating voltage.
• Always switch the vacuum cleaner off and unplug
it while replacing the brush-attachments and dur-
ing maintenance.
Attaching and removing the flexible hose
• Insert the flexible hose ending (8) into the air in-
let (9), matching the ledges on the ending with the
grooves in the air inlet, and turn the ending clock-
wise (pic. 1).
• To remove the flexible hose turn the flexible hose
ending (8) counterclockwise and detach the hose.
Attaching the telescopic pipe and the brush-
attachments
• Attach the telescopic extension pipe (4) to the han-
dle of the flexible hose (6) (pic. 2).
• Extend the lower part of the telescopic extension
pipe to the required length, having preliminarily
pressed the button of the lock (3) (pic. 3).
• Choose the necessary attachment - floor/carpet
brush (1), turbo brush (26) or combined attach-
ment (27) - and attach it to the telescopic extension
pipe (4) (pic. 4).
Floor/carpet brush (1)
Set the switch (2) on the brush (1) to the required
position (depending on the type of the surface being
cleaned).
Turbo brush (26)
You can use the turbo brush (26) for cleaning floors
and carpets with medium and low pile, it is perfect for
removing pet hair from carpets. The cylindrical hard-
bristled brush is brought to rotation by the air flow, its
bristles comb out pet hair out thoroughly and sweep the
motes out of the carpet pile.
Note: Do not use the turbo brush for cleaning the
carpets with high fringe and pile of more than 15 mm
1826.indd 4
to avoid carpet damaging by brush rotation. Do not run
the turbo brush over electric wires, after cleaning is
completed, switch the vacuum cleaner off immediately
after usage of the turbo brush.
Combined attachment (27)
This attachment is intended not only for cleaning
radiators, crevices, corners and space between
cushions, but also for collecting dust from furniture
surface as well; pile prevents the damage of polished
furniture surface.
Note: - Always switch the vacuum cleaner off and take
the power plug out of the socket before replacing the
brush attachments and cleaning the dust bin (11).
USING THE VACUUM CLEANER
Attention! Always switch the vacuum cleaner on
only with the dust bin (11), inlet filter (20), outlet
HEPA-filter (17) and protective (25) filter installed.
Always check if the dust bin (11) is assembled
properly and the filters (17, 20, 25) are installed
properly.
• Before using the unit, unwind the power cord to the
required length and insert the power plug into the
mains socket. The yellow mark on the power cord
warns about the maximum cord length. Do not un-
wind the power cord further than the red mark.
• Press the on/off button (13) to switch the vacuum
cleaner on.
• During the operation you can control the suction
power using the suction power control (14) and the
mechanical control (5) on the flexible hose han-
dle (6).
• After the unit operation switch the vacuum cleaner
off by pressing the button (13) and unplug the unit.
• To wind the power cord press and hold the button
(18), hold the winding cord with hand to avoid its
whipping and damage.
• Between operations use the brush storage (15).
• Use the handle (10) for carrying the vacuum cleaner
or the dust bin (11).
CLEANING AND CARE
Remove garbage and dust from, disassemble and
clean the dust bin (11) after every usage of the vacuum
cleaner.
Start cleaning only after removing dust and garbage
from the dust bin (11).
Removing of the dust bin (11) and removal of dust
and garbage from it
• Switch the vacuum cleaner off by pressing the on/
off button (13) and unplug it.
• Holding the handle (10), press the release button
(12) and remove the dust bin (11) (pic. 5).
• Place the dust bin over a garbage bin. Open the
lid (23) by pressing the lid lock (24) (pic. 6). Re-
move accumulated dust and garbage from the dust
bin (11).
4
11.10.2013 16:25:12
Werbung
Inhaltsverzeichnis
