Assembling The Vacuum Cleaner - Vitek VT-1842 G Die Betriebsanweisung

– the inlet, outlet and protective filters are not
installed.
• Make sure regularly that the power plug and
the power cord are not damaged. Do not try
to repair the unit by yourself. Contact an au-
thorized service center for all repair issues.
• Never allow children to use the vacuum
cleaner as a toy. Close supervision is neces-
sary when children or disabled persons are
near the operating unit.
This unit is not intended for usage by children
•
or disabled persons unless they are given all
the necessary and understandable instruc-
tions by a person who is responsible for their
safety on safety measures and information
about danger that can be caused by improper
usage of the unit.
For children safety reasons do not leave poly-
•
ethylene bags, used as a packaging, unat-
tended.
Attention! Do not allow children to play with
polyethylene bags or packaging film. Danger of
suffocation!
• Keep the unit out of reach of children.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY

ASSEMBLING THE VACUUM CLEANER

After unit transportation or storage at low
temperature it is necessary to keep it for at
least two hours at room temperature before
switching on.
– Unpack the unit completely and remove any
stickers that can prevent unit operation.
– Check the unit for damages; do not use the
unit in case of damages.
– Before switching the unit on make sure that
your home mains voltage corresponds to unit
operating voltage.
Attaching the flexible hose, the telescopic
pipe and the attachments
– Insert the flexible hose ending (11) into the air
inlet (10) till the locks click (pic. 1). To remove
the flexible hose (12) press the ending locks
(11) and detach the hose (12).
– Insert the flexible hose handle (13) into the
telescopic extension pipe (15) (pic. 2).
VT-1842_IM.indd 5
– Extend the lower part of the telescopic exten-
sion pipe to the required length, having pre-
liminarily pressed the lock (16) (pic. 3).
– Select the required attachment - for instance,
floor/carpet brush (17), dust brush (20), fur-
niture upholstery cleaning attachment (21) or
crevice nozzle (22) - and attach it to the tele-
scopic extension pipe (15) (pic. 4).
– The dust brush (20), furniture upholstery
cleaning attachment (21) or the crevice noz-
zle (22) can be attached directly to the flex-
ible hose handle (13).
Floor/carpet brush (17)
Set the «floor/carpet» switch (18) on the brush
(17) to the required position (depending on the
type of the surface being cleaned).
Turbo brush (19)
You can use the turbo brush (19) for cleaning floors
and carpets with medium and low pile, it is perfect
for removing pet hair from carpets. The cylindrical
hard-bristled brush is brought to rotation by the
air flow, its bristles comb out pet hair thoroughly
and sweep motes out of the carpet pile.
Note:
– Do not use the turbo brush for cleaning car-
pets with high fringe and pile of more than
15 mm to avoid carpet damaging by brush
rotation.
– Do not run the turbo brush over electric wires
and switch the vacuum cleaner off right after
cleaning with the turbo brush.
Dust brush (20)
This brush (20) is intended for collecting dust
from furniture surface, pile prevents damage of
polished furniture surface.
Furniture upholstery cleaning attachment
(21)
The attachment (21) is intended for cleaning of
fabric surfaces of upholstered furniture.
Crevice nozzle (22)
The crevice nozzle (22) is intended for cleaning
radiators, chinks, corners and spaces between
cushions.
Note: Attachments (20 and 22) are stored inside
the unit body under the dust bin (9).
Note: Always switch the vacuum cleaner off and
take the power plug out of the socket before
replacing the brush attachments and before
cleaning the dust bin (9).
5
ENGLISH
14.10.2013 11:38:55