Herunterladen Inhalt Inhalt Diese Seite drucken

WAGNER AC20 Bedienungsanleitung Seite 38

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
#
Sender's SMTP Password :
* Enter the password for the email address (e.g.
the password for SamSample@gmail.com) from which you want the
emails to be sent here, and confirm with "Done".
#
Send mail when Internet IP address changes:
Keep the factory setting.
Factory setting: OFF
Notes:
#
The TLS encryption protocol that is required to send emails
by some providers. If necessary, set up a free email account, e.g. with
Google Mail (gmail).
#
If your "Sender's Email" is a Google account, it may be necessary to
activate access for "less secure apps" under "Security" in the email address
settings.
12.2.7 Automatic recording following motion detection or according to a
Schedule [50 - Recording (Alarm), Format and Motion Detection]
The following settings are possible:
+
Both motion detection and automatic recording are activated:
Both settings are set to OFF
+
Only motion detection is activated,
Motion Detection is set to ON, Enable Recording is set to OFF
+
If motion is detected, a 59-second recording will automatically be saved
on the micro-SD card:
"Motion Detection" and "Enable Recording" are set to ON - no time
period is activated in the schedule
Compared to a continuous recording according to a schedule, recordings
following motion detection require less storage space, and it is easier to
search for events.
Note:
To be able to quickly switch on and off the recording following motion
detection, first set "Enable Recording" to ON in the settings. This can
be done directly via "Guard" [41] in the menu bar.
+
In accordance with the pre-set schedule, recordings are made during the
specified time periods. In each case for four full hours, divided into
sequential 15-minute files (i.e. 16 files are recorded during a 4-hour
period). The rest of the time, outside of the specified time periods, there are
no recordings or, depending on the settings, no recordings following
motion detection.
"Enable Recording" is set to ON, at least one time period has been
specified in the schedule (Edit Schedule), "Motion Detection" is set to
ON or OFF.
#
Enable Recording (Alarm):
(depending on other settings either following motion detection or
according to a schedule); when set to OFF, it is disabled
Factory setting: ON
#
Edit Schedule:
Setting up the schedule for a continuous 4-hour recording,
divided into 15-minute sequences. You can activate individual time
periods, whole columns or rows, or the entire week (mark blue)
Factory setting: No continuous recording
IMPORTANT NOTE:
38 - GB
without
recording:
When set to ON, automatic recording is enabled
The revised schedule must be confirmed with "Save" two times: Once
after the time periods have been set, and another time immediately
afterwards.
#
Record frame: 15 or 30 frames/second are recorded
Factory setting: 15 images/second (requires less storage space)
#
Format MicroSD Card:
inserted in the camera. Please note, however, that all previously saved
data will be deleted in the process.
is not supported
#
Enable Motion Detection:
detection; if set to OFF, it is disabled
Factory setting: ON
#
Sensitivity:
very sensitive / 10 - very sensitive)
Factory setting: 5
12.2.8 Update Firmware / Restore Factory Settings / Restart
Camera [51 - Tools]
!
Update Firmware:
automatically search for new firmware. If a new one is detected, confirm
with "OK" in the following field. The app will now load the firmware
automatically, after which the camera will shut down and restart
automatically. The connection LED [6] goes out. As soon as it is
permanently lit again, the camera has restored the connection to the
router. Now wait until the connection indicator [19] appears in the camera
field (if it does not appear, close and restart the app).
!
Restore Factory Settings:
At the same time the camera is restarted, so that access must be set up
again on all mobile devices: Press this field and then confirm with "OK".
Now deleted the camera field of the old connection with "Delete" [43].
Once the camera's connection LED [6] starts to blink, carry out the initial
setup process as described in Chapter 6.1 from section six onwards. If more
mobile devices had access to the camera, delete the camera field there too
and then proceed as described in Chapter 9.2 from section two onwards.
!
Restart System:
settings), press this field and then "OK". The connection LED [6] will go out.
Once it is permanently lit again, the camera has restored the connection to
the router. Now wait until the connection indicator [19] appears again in
the camera field (if it does not appear, close and restart the app).
12.3 Activate/Deactivate motion detection [41 - Guard]
!
Here you can switch motion detection on and off.
!
To sa
Note:
Automatic recording is not automatically switched on/off too, i.e. changing the
settings to "ON" will only trigger a recording following motion detection if
"Enable Recording" is also set to ON.
12.4 Change the camera name [42 - Edit]
Here you can change the camera name (Name) that is shown at the top of the
camera field for the corresponding mobile device.
!
In the "Name" field, enter the desired camera name and confirm with
"Save".
Here you can format the micro-SD card that is
When set to ON, recording is activated by motion
Here you
can adjust the motion detection sensitivity (1 - not
Only if required: press this field. The app will
Here all settings are reset to the factory settings.
To restart the camera automatically (retaining all
ve your settings, press "Save".

Werbung

Inhaltsverzeichnis

Fehlerbehebung

loading

Inhaltsverzeichnis