Care Of The Unit; Return Of Old Electric And Electronic Equipment For Disposal; Collection; Return And Collection Systems - 3M ESPE Visio Beta vario Betriebsanleitung

Turn the unit off and pull the power plug from its socket!
reflector located behind the lamps is contaminated, clean it
with a cloth dampened in alcohol.
Caution: Do not scratch the reflector with any hard objects!
Place new fluorescent lamps LB1 in the respective holders.
Replace the cover plate and fix in place by tightening the six
screws.
Replacement of the lower pair of lamps
Empty the polymerization
chamber and close the lid.
Turn the unit off
and pull the
power plug
from its socket!
Place the unit
on its right side.
Unscrew the screw located in the bottom door and remove the
door.
Caution: Do not scratch the reflector with any hard objects!
Place new fluorescent lamps LB 1 in the respective holders.
Attach bottom door by its hinges, close the door and tighten
the screw.

9. Care of the unit

Clean all components with a soft cloth and, if necessary, a mild
cleaning agent (e. g. dish-washing detergent). Solvents or
abrasive cleaners may not be used in any case, as they can
damage the plastic components! Cleaning agents must not
enter the unit!
To disinfect all components, spray the disinfectant on a towel
and use it to disinfect the unit. Do not spray the disinfectant
directly on the device. Disinfectant agents must not enter the
unit! Dry residual disinfectants on the device with a soft and
fluff-free cloth, as they damage the plastic components.
If necessary, ask the manufacturer of the disinfectant if its
constant use will damage plastic surfaces.
Any contamination inside the polymerization chamber should
be removed with alcohol. Persistent contaminating material
4
Unscrew the six screws
located in the cover
plate, and remove both
the cover plate and
glass plate.
Clean both sides of the
glass plate with a cloth
dampened in alcohol.
Remove the two lamps
from their respective
holders by pulling in an
upward direction. If the
Remove the two fluorescent
lamps from their respective
holders by pulling in an
upward direction.
Clean the bottom door
reflector and the bottom side
of the glass cup with a cloth
dampened in alcohol.
should be soaked by placing an alcohol-saturated piece of
cloth inside the chamber and closing the cover (Do not press
the Start-Stopp button!). After extended soaking (preferably
over night) use a plastic spatula to remove residues of the
working materials from the polymerization chamber and glass
plate. Do not use a metal instrument for this purpose!
Fluorescent lamps must be cleaned/dusted at least at semi-
annual intervals to ensure proper performance of the lamps.
For details on how to clean reflectors and fluorescent lamps,
please refer to the section on "Replacement of upper/lower
pair of lamps".
10. Return of Old Electric and
Electronic Equipment for Disposal

10.1 Collection

Users of electric and electronic equipment are required to
collect their old equipment separately from other waste in
accordance with the regulations of the specific country. Old
electric and electronic equipment must not be disposed of
with unsorted household waste. This separate collection is a
prerequisite for recycling and reprocessing as an important
method for preserving environmental resources.

10.2 Return and Collection Systems

When your Visio Beta vario is no longer usable, do not dispose
of the device with household waste. 3M Deutschland GmbH
has set up special disposal facilities to handle the equipment.
Details about the procedure for the specific country can be
obtained from the pertinent 3M subsidiary.
The Visio Beta vario lamp contains mercury, dispose according
to local, state or federal laws.

10.3 Meaning of the Symbols

The EU Directive prohibits the disposal of any electric
or electronic devices marked
with these symbols in
combination with household
waste.

11. Customer Information

No person is authorized to provide any information which
deviates from the information provided in this instruction sheet.
Warranty
3M Deutschland GmbH warrants this product will be free from
defects in material and manufacture. 3M Deutschland GmbH
MAKES NO OTHER WARRANTIES INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. User is responsible for determining the
suitability of the product for user's application. If this product
is defective within the warranty period, your exclusive remedy
and 3M Deutschland GmbH's sole obligation shall be repair or
replace ment of the 3M Deutschland GmbH product.
Limitation of Liability
Except where prohibited by law, 3M Deutschland GmbH will
not be liable for any loss or damage arising from this product,
whether direct, indirect, special, incidental or consequential,
regardless of the theory asserted, including warranty, contract,
negligence or strict liability.
Information as of August 2014