Operation Section; Correct Usage - Toshiba RAV-SM408CTP-E Bedienungsanleitung

Operation section

Push each button to select a desired operation.
The control saves commands in memory and after the initial setting, there is no need for any additional
settings unless changes are desired. The air conditioner can be operated by pushing the
1
2
3
4
1
button (Temperature set button)
Adjusts the set point.
Select the desired set point by pushing
or TEMP. .
2
button (Timer set button)
Use to setup the timer.
3
button (Filter reset button)
Resets " " display after cleaning filter.
4
button (Test button)
Use only for service.
(During normal operation, do not use this button.)
5
button
When the button is pushed, the operation starts, and
it stops by pushing the button again.
When the operation has stopped, the operation
lamp and all the displays disappear.
6
Operation lamp
Green light illuminates when unit is on.
Although it flashes when the protection device is
operated or an error occurs.
7
button (Operation mode button)
Selects desired operation mode.
8
button (Fan speed button)
Selects the desired Fan speed.
87-EN
1114653801_EN.indb 44 1114653801_EN.indb 44
5
6
7
8
9
10
11
12
9
button (Ventilation button)
Use when a power ventilation kit (locally procured)
is connected.
TEMP.
If " " is displayed on the remote controller
when this button is pushed, no vent kit
connected.
10
button (Power save operation)
Use to initiate power saving mode.
11
button (Unit / Louver select button)
Selects a unit number (left) and louver number
(right).
UNIT:
Selects an indoor unit when adjusting wind
direction multiple indoor units are controlled with
one remote controller.
LOUVER:
Selects a louver when wind direction adjustment is
set independently.
12
button (Swing / Louver direction
button)
Selects automatic swing or setting the louver
direction.
OPTION:
Remote controller sensor
Usually the temperature sensor of the indoor unit
senses the temperature. The temperature on the
surrounding of the remote controller can also be
sensed.
For details, contact the dealer from which you have
purchased the air conditioner.
4

Correct usage

When the air conditioner is used for the first time or when the setting is changed, follow the steps below. Settings
are saved in memory and are displayed anytime the unit is turned on by pushing the
button.
Preparation
When the circuit breaker is turned on, the partition lines are displayed on the remote controller.
* After the circuit breaker is turned on, the remote controller does not accept any commands for approx. 1 minute,
this is not a failure.
REQUIREMENT
When the air conditioner is re-powered after it has not been used for a long period, turn on the circuit breaker at least
12 hours before starting the air conditioner.
TEMP.
4
TIMER SET FAN
TIME SAVE
FILTER
RESET TEST SET CL SWING/FIX
Start
1
Push button.
The operation lamp illuminates, and the operation
starts.
2
Select an operation mode with the "
button.
One push of the button, and the display changes
in the order shown below.
Auto Heat Dry
(Dehumidify)
– 44 –
3
Select fan speed with "
One push of the button, and the display changes
in the order shown below.
Auto High
ON / OFF
1
When fan is in "
3
adjusted based on difference between set point
2
MODE
and room temperature.
VENT
In heating operation, if the room temperature is
UNIT LOUVER
not heated sufficiently with speed "
operation, select "
operation.
The temperature sensor detects the return air
temperature at the indoor unit, which differs
from the room temperature depending on the
installation condition.
Set point is a target of room temperature.
( "Auto" is not selectable in the Fan
"
mode.)
4
Select the set point temperature by pushing
the "TEMP. " or "TEMP.
Stop
Cool Fan
Push button.
The operation lamp goes off, and the operation stops.
button.
" button.
Med. Low
Auto", fan speed is
Low"
Med." or " High"
" buttons.
EN
EN
ID
88-EN
10/4/16 1:46 PM 10/4/16 1:46 PM