Specifications - DNP DP-DS80D Leitfaden Zur Inbetriebnahme

・
Do not install the product in dusty or humid places. This may cause fire or an electric shock, or damage the product.
・
Do not install the product on an unstable surface. It may fall and cause injury to the user or other people.
・
Do not allow foreign objects to enter into the product. They may cause an electric shock, a short circuit, or fire, or damage the product. If something falls into
the product, immediately turn the power off, unplug the power cord, and call a service representative.
・
Do not open the cover while printing. This may damage the product.
・
Do not spill or spray liquids or chemicals onto the product.
・
When cleaning the cover, do not use thinner, trichloroethane, benzene, ketone-based cleaners, or chemically treated cloths. They could discolor or
deteriorate the cover.
・
At least once a year, unplug the power cord, and clean the prongs and the plug. If dust accumulates, it may cause a fire.
・
When printing continuously for long periods in a small room, be sure to ventilate the room properly.
・
If you intend to use the product on a transportation vehicle (train, truck, ship, etc.), please talk to a representative in advance.
・
When disposing of the product, accessories, packaging materials, or media (paper, ribbon), please abide by local waste removal ordinances. For details,
contact your local government offices.
・
When unplugging the cord, always grip the plug. Do not pull on the cord as it may damage the cord and cause an electric shock or fire.
・
When moving the product, be sure to unplug the power cord. Otherwise, the cord may be damaged, which may cause fire or an electric shock.
・
For safety, when not using the product for an extended period of time, be sure to unplug the power cord. Otherwise, it may cause an electric shock, fire, or a
malfunction.
・
Parts with this warning get extremely hot. Do not touch these parts after printing. There is a danger of burns.
・
Do not touch the gear mechanisms. There is a danger of injury if fingers get caught in spinning gears.
・
Do not put your fingers inside the parts showing this mark. There is a danger of injury.
Caution for installation
・
Before using the product, read "For Safe Operation" carefully and observe the instructions therein.
・
Use care when moving the product. Never try to carry the product alone. Dropping it may cause injury or property damage.
・
Do not use or store the product near a fire, humid places, in direct sunlight, near an air conditioner or heater, or any other location with unusually high or low temperature,
strong humidity, or excessive dust.
・
Do not place the product where chemical reactions occur, such as in a laboratory.
・
Do not install the product where there is salinity or corrosive gas in the air.
・
The product must be installed on a firm, level surface where there is ample ventilation.
・
Do not put anything on top of the product.
・
Do not use the product near a radio or television, and do not use the same wall outlet for the product and a radio or television. Otherwise radio or television reception may be
adversely affected.
・
Do not use a power voltage or a frequency other than those specified.
・
Do not put anything on the power cord or step on it.
・
Do not drag or carry the product by the power cord or the USB cable.
・
Avoid plugging the power cord into an outlet with many other cables connected.
・
Do not bundle the power cord.
・
Always grip the plug housing, not the cord, to plug or unplug the power cord.
・
Make certain the power is turned off before connecting or disconnecting the USB cable.
・
Avoid using a long USB cable or connecting it to any noise-producing device. If it is unavoidable, use a shielded cable or twisted pair for each signal.
・
Use a shielded USB cable compatible with the USB 2.0 specifications.
・
Place the product near the outlet where the power cord can be unplugged easily to shut the power off.
・
Use an AC outlet that accepts a three-pronged plug. Otherwise, there may be a danger of electric shock.
・
Do not use the cord set supplied with the printer for other devices.
・
Use the cord set supplied for the product.
・
Only use items that are certified safe according to the standards of the country where they are to be used.
・
Make sure the blind plates are installed when not using the Turning Unit. Otherwise, there may be a danger of fire.

Specifications

Print method
Dimensions
Weight
Rated voltage
Thermal dye sublimation transfer
322 mm（W）×367 mm（D）×171 mm（H）
Approx. 14.0 kg (printer unit only)
AC100 V – 240 V 50 Hz/60 Hz
Caution
Rated current
Temperature 5°C to 35°C in natural convection conditions
Operating environment
100 V 3.96 A 240 V 1.69 A
Humidity 35% to 80% with no condensation