Functional Description - Makita DHS782 Betriebsanleitung

FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
WULGJH ¿UPO\ ZKHQ LQVWDOOLQJ RU UHPRYLQJ EDWWHU\
cartridge. )DLOXUH WR KROG WKH WRRO DQG WKH EDWWHU\
FDUWULGJH ¿UPO\ PD\ FDXVH WKHP WR VOLS RII \RXU KDQGV
DQG UHVXOW LQ GDPDJH WR WKH WRRO DQG EDWWHU\ FDUWULGJH
DQG D SHUVRQDO LQMXU\
CAUTION:
Always bring down the base when
installing/removing the batteries. Be careful not to
SLQFK \RXU ¿QJHUV
CAUTION:
Do not use the battery adapter with
the circular saw. The cable of the battery adapter
may hinder the operation and result in personal
injury.
Fig.7: 1. Lever 2. Red indicator 3. Button 4. %DWWHU\
cartridge
%HIRUH UHPRYLQJ WKH EDWWHU\ FDUWULGJH ORRVHQ WKH OHYHU
IRU GHSWK DGMXVWPHQW WR ORZHU WKH WRRO EDVH 7KHQ VOLGH
WKH EDWWHU\ IURP WKH WRRO ZKLOH VOLGLQJ WKH EXWWRQ RQ WKH
front of the cartridge.
7R LQVWDOO WKH EDWWHU\ FDUWULGJH DOLJQ WKH WRQJXH RQ WKH
EDWWHU\ FDUWULGJH ZLWK WKH JURRYH LQ WKH KRXVLQJ DQG VOLS
LW LQWR SODFH ,QVHUW LW DOO WKH ZD\ XQWLO LW ORFNV LQ SODFH
ZLWK D OLWWOH FOLFN ,I \RX FDQ VHH WKH UHG LQGLFDWRU RQ WKH
XSSHU VLGH RI WKH EXWWRQ LW LV QRW ORFNHG FRPSOHWHO\
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
LW PD\ DFFLGHQWDOO\ IDOO RXW RI WKH WRRO FDXVLQJ LQMXU\ WR
\RX RU VRPHRQH DURXQG \RX
CAUTION:
Do not install the battery cartridge
forcibly. ,I WKH FDUWULGJH GRHV QRW VOLGH LQ HDVLO\ LW LV
QRW EHLQJ LQVHUWHG FRUUHFWO\
NOTE: 7KH WRRO GRHV QRW ZRUN ZLWK RQO\ RQH EDWWHU\
cartridge.
Tool / battery protection system
7KH WRRO LV HTXLSSHG ZLWK D WRROEDWWHU\ SURWHFWLRQ V\V-
WHP 7KLV V\VWHP DXWRPDWLFDOO\ FXWV RII SRZHU WR WKH
PRWRU WR H[WHQG WRRO DQG EDWWHU\ OLIH 7KH WRRO ZLOO DXWR-
PDWLFDOO\ VWRS GXULQJ RSHUDWLRQ LI WKH WRRO RU EDWWHU\ LV
placed under one of the following conditions.
Overload protection
:KHQ WKH WRRO LV RSHUDWHG LQ D PDQQHU WKDW FDXVHV LW WR
GUDZ DQ DEQRUPDOO\ KLJK FXUUHQW WKH WRRO DXWRPDWLFDOO\
stops. In this situation, turn the tool off and stop the
application that caused the tool to become overloaded.
Then turn the tool on to restart.
Overheat protection
:KHQ WKH WRRO LV RYHUKHDWHG WKH WRRO VWRSV DXWRPDWL-
FDOO\ DQG WKH EDWWHU\ LQGLFDWRU EOLQN DERXW  VHFRQGV
In this situation, let the tool cool down before turning the
tool on again.
On
Overdischarge protection
:KHQ WKH EDWWHU\ FDSDFLW\ EHFRPHV ORZ WKH WRRO VWRSV
DXWRPDWLFDOO\ ,I WKH SURGXFW GRHV QRW RSHUDWH HYHQ
when the switches are operated, remove the batteries
from the tool and charge the batteries.
Indicating the remaining battery
capacity
Fig.8: 1. %DWWHU\ LQGLFDWRU 2. Check button
3UHVV WKH FKHFN EXWWRQ WR LQGLFDWH WKH UHPDLQLQJ EDWWHU\
FDSDFLWLHV 7KH EDWWHU\ LQGLFDWRUV FRUUHVSRQG WR HDFK
EDWWHU\
Battery indicator status
On Off
14 ENGLISH
Blinking
Remaining
battery
capacity
Blinking
50% to 100%
20% to 50%
0% to 20%
Charge the
EDWWHU\