Sparky CMW 1212CE Originalbetriebsanleitung Seite 14

be possible to use both hands for convenient
and safe assembly.
3. Press the spindle lock button (3) and ro-
tate the brush (11) clockwise until the button (3)
sinks and locks the spindle (1).
4. Take the brush (11) and rotate it anti-clock-
wise until the brush (11) is entirely unscrewed
from the spindle M14 thread.
5. Remove the support flange (9) from the
spindle (1).
6. Clean the face surface and the opening
of the support flange (9) and the flexible back-
ing pad (10) by a brush and soft cloth and store
them for future use.
POLISNING WITH DIAMOND PARTICLE
PAD
The choice of the pad depends on the opera-
tion you intend to perform. To achieve good re-
sults it is necessary to process the surface at
least twice; use coarser pads (with smaller grit
number) for the first processing; use fine struc-
ture pads (with bigger grit number) for finishing.
The operator estimates the quantity of the fed
liquid, considering the fact that the liquid cools
the operating tool and improves the quality of
the processed surface.
We recommend using original SPARKY acces-
sories specially designed for achieving optimum
results.
Use only pads with hook-and-loop fastening.
Never use consumables and accessories with
diameter exceeding the maximum permitted for
the power tool.
CLEANING WITH NONWOVEN fABRIC
(fIBRAT) PAD
Cleaning with a nonwoven fabric (Fibrat) pad(17)
is carried out to remove the dirt from surfaces
which allow the use of liquids during operation.
The operator estimates the quantity of the fed
liquid, considering the fact that the liquid cools
the operating tool and improves the quality of
the processed surface.
We recommend using original SPARKY acces-
sories specially designed for achieving optimum
results.
Use only pads with hook-and-loop fastening.
Never use pads with diameter exceeding the
maximum permitted for the power tool.
12
EN
CLEANING WITH A BRUSH
Cleaning with brushes (11) is carried out to re-
move the dirt from surfaces which allow the use
of liquids during operation.
The operator estimates the quantity of the fed
liquid, considering the fact that the liquid cools
the operating tool and improves the quality of
the processed surface.
We recommend using original SPARKY acces-
sories specially designed for achieving optimum
results.
Use only brushes with M14 thread.
Do not use brushes with diameter exceeding the
maximum permitted for this power tool.
MOUNTING THE DIAMOND PARTICLE
PAD AND THE NONWOVEN fABRIC
(fIBRAT) PAD
1. Ensure that the power tool is unplugged
and the liquid feed system is not under pres-
sure.
2. Turn the machine in a way ensuring ac-
cess to the operating tool. We recommend fixing
the machine in stationary position. Thus it would
be possible to use both hands for convenient
and safe assembly.
3. Tighten the flexible pad (10) firmly, while
performing the procedures according items 8, 9
и 10 from section „Mounting the flexible pad
4. Place the selected operating tool, taking
care to ensure its coaxiality toward the flexible
pad (10).
5. Ensure the concentricity of the chosen op-
erating tool for better work.
6. Press the face of the operating tool to the
flexible pad (10) to ensure maximum cohesion
between their hook-and-loop surfaces.
7. Turn the machine so that the operating
tool faces the floor.
8. Plug in the power tool.
9. Set the electronic regulator (16) to its
maximum position for the specific operating tool
according to the recommended values. Switch
on the PRCD and check it functioning. Switch on
the PRCD by pressing the ON-I-RESET button.
Switch on the machine by sliding the ON/OFF
switch (5) forward.
10. Let the machine operate at no load for ap-
proximately one minute, not allowing the operat-
ing tool to contact any surface.
11. At the event of increased vibrations or
other symptoms not typical for operation, stop
the machine immediately and search for the
reason. If you can not detect the reason your-
PMW 1212CE ● CMW 1212CE