Werbung
Verfügbare Sprachen
Verfügbare Sprachen
N. POWER SWITCH - Switches the amplifier on-off.
O. IEC POWER SOCKET - Connect the power cord
(included) to a grounded AC receptacle in
compliance with the voltage and frequency ratings
specified on the rear panel of your amplifier.
P. TUNER - Connect your guitar tuner here.
MUTE {I} to silence audio output while tuning.
Q. LINE OUT - Balanced XLR jack for output to sound
reinforcement and recording equipment.
TYPE:
PART NUMBERS:
POWER REQUIREMENT:
PREAMP
INPUT IMPEDANCE: PASSIVE: 1MΩ
SENSITIVITY AT FULL POWER: PASSIVE: 19mV
NOMINAL LEVEL: PASSIVE: 145mV
POWER AMP
SENSITIVITY: 1.4V R.M.S., 1kHz
POWER OUTPUT: 200W R.M.S. into 4Ω @ < 0.02 % T.H.D., 1 kHz
TONE CONTROLS
EQ TILT: ±10dB, crossover frequency: 350Hz
BASS/TREBLE: BASS: ± 15dB @ 50Hz
SEMI-PARAMETRIC MID: MID FREQ: 200Hz to 1.0 kHz
EFFECTS LOOP
IMPEDANCES: SEND: 1kΩ
NOMINAL LEVEL: +4dBu (adjustable with level control)
FOOTSWITCH:
SPEAKER:
FITTED COVER:
DIMENSIONS:
WEIGHT:
w
w w
w w
w . . f f e
e n
n d
d e
Use
PR 411
2289500000 (120V, 60Hz) USA
2289506000 (230V, 50Hz) EUR
540W
Three button, included: Reverb, Tuner Mute, Effects Loop (064544)
One 15", 4Ω Fender
®
Custom 15 Driver, made in USA by Eminence
Included (065532)
HEIGHT: 21 in (53.3 cm)
65 lb (24.3 kg)
Product specifications are subject to change without notice.
e r
r . . c
c o
o m
m
w w
w
R R
R. GROUND LIFT - Disconnects the LINE OUT {Q}
ground connection (pin-1) which may reduce hum
noise in some situations.
GROUNDED (normal)
S. PRE/POST EQ - Supplies the LINE OUT jack with
the signal either before or after it is processed by the
amplifier's tone and equalization circuits.
PRE (tone/EQ bypassed)
POST (tone/EQ active)
T. LINE OUT LEVEL - Adjusts the signal output level
of the LINE OUT jack {Q}.
U. FOOTSWITCH - Connect the included footswitch to
enable remote on-off switching of REVERB,
TUNER MUTE and the EFFECTS LOOP.
When connected, the footswitch buttons override
the corresponding controls on the front panel.
V. FX SEND / FX RETURN - (1) Effects Loop -
Connect FX SEND to your effects input and effects
output to FX RETURN. (2) Multiple Amps - Connect
FX SEND on the primary unit to FX RETURN on the
auxiliary unit. The primary unit controls all auxiliary
units.
S S
S S
p p
p p
e e
e e
2289503000 (240V, 50Hz) AUS
2289509000 (220V, 60Hz) ROK
ACTIVE: 1MΩ
ACTIVE: 40mV
ACTIVE: 300mV
TREBLE: ± 15dB @ 10kHz
MID LEVEL: ±15dB @ MID FREQ setting
RETURN: 22kΩ
®
(064398)
WIDTH: 20 in (50.8 cm)
w w
w . . m
m r
r g
g e
e a
e e
a a
r r
P P
a a
n n
e e
l l
R R
e e
a a
r r
P P
a a
n n
e e
l l
GROUND LIFTED
NOTE:
c c
c c
i i
i i
f f
f f
i i
i i
c c
c c
a a
a a
t t
t t
i i
i i
o o
o o
n n
n n
s s
s s
2289504000 (230V, 50Hz) UK
DEPTH: 12.5 in (31.8 cm)
a r
r h
h e
e a
a d
d . . n
n e
7
e t
t
Werbung
