Specifications; General Safety Rules - Makita 4101RH Betriebsanleitung

ENGLISH
1 Wing bolt
2 Water pipe
3 Hex wrench 5
4 Loosen
5 Tighten
6 Wrench 22
7 Inner flange
8 Diamond wheel
9 Outer flange
10 Hex socket head bolt
11 Base

SPECIFICATIONS

Model
Wheel diameter ............................................ 125 mm
Max. cutting capacities
At 90° ....................................................... 41.5 mm
At 45° .......................................................... 26 mm
-1
No load speed (min ) .................................... 12,000
Overall length ............................................... 236 mm
Net weight ........................................................2.9 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.

GENERAL SAFETY RULES

WARNING! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury. The term "power tool" in all of the
warnings listed below refers to your mains-operated
(corded) power tool or battery-operated (cordless) power
tool.
SAVE THESE INSTRUCTIONS.
Work area safety
1. Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while oper-
ating a power tool. Distractions can cause you to
lose control.
6
Explanation of general view
12 Wing nut
13 This end of blade case should
be above the red line.
14 Red line
15 "TEST" button
16 "ON" button
17 Pilot lamp
18 Portable residual current
device (PRCD)
19 Switch trigger
20 Lock-off button
Electrical safety
4.
4101RH
5.
6.
7.
8.
Personal safety
9.
10. Use safety equipment. Always wear eye protec-
11. Avoid accidental starting. Ensure the switch is in
12. Remove any adjusting key or wrench before
13. Do not overreach. Keep proper footing and bal-
21 Top guide
22 For straight cuts
23 For 45° bevel cuts
24 Clamp
25 Cover (A)
26 Screw
27 Cover (B)
28 Limit mark
29 Brush holder cap
30 Screwdriver
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
tion. Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal inju-
ries.
the off-position before plugging in. Carrying
power tools with your finger on the switch or plug-
ging in power tools that have the switch on invites
accidents.
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
ance at all times. This enables better control of the
power tool in unexpected situations.