Displaying The Indoor Temperature; Displaying Temperatures In °C / °F; Displaying The Air Humidity (Indoor); Displaying The Maximum / Minimum Temperature / Humidity - Auriol Z29536 Bedienungs- Und Sicherheitshinweise

Operation / Troubleshooting
Displaying the indoor
Q 
temperature
The current Indoor temperature
the LC display.
Displaying temperatures
Q 
in °C / °F
note: °C is the legally required temperature unit.
note: The weather station is supplied in the
default setting of °Celsius.
j
Press the "+" / °C / °F button
between the Celsius and Fahrenheit tempera-
ture scales.
Displaying the air humidity
Q 
(indoor)
The current air humidity
display. The Comfort indicator
air humidity in three categories.
The following categories are available:
"Dry" = Air humidity
"Comfort" = Air humidity
indoor temperature
24 °C - 27.9 °C
"Wet" = Air humidity
Displaying the Maximum /
Q 
Minimum Temperature /
Humidity
The minimum / maximum temperature / humidity is
measured for the first time after the batteries have
been inserted and stored in the weather station.
j
Press the "–" / MAX / MIN button
The maximum indoor
perature measured and the maximum
24
humidity measured are shown.
5
j
Press the "–" / MAX / MIN button
briefly. The minimum indoor
temperature measured and the minimum
24
humidity measured are shown.
5
j
Press the "–" / MAX / MIN button
briefly to return to the current values.
note: If no button is pressed within 5 seconds,
the displays automatically return to the
standard display.
j
Hold the "–" / MAX / MIN button
for approx. 3 seconds in order to delete the
stored maximum and minimum values when
you hear a beep sound. The values measured
from the time of deletion of the old values
until the next time the memory is called up
can be called up again.
12 GB/CY
is shown in
3
to switch
28
is shown in the LC
5
displays the
4
< 45 %
5
45 - 75 %,
5
3
> 75 %
5
briefly.
29
and outdoor tem-
3
again
29
and outdoor
3
again
29
down
29

Backlight

Q 
j
Press the SNOOZE / LIGHT button
backlight illuminates for 3 seconds.

Battery state display

Q 
The Battery state indicator
weather station's LC display if the batteries are
weak. Make sure you replace the batteries at the
earliest opportunity (see "Replacing the batteries").

Replacing the batteries

Q 
Weather station:
You should replace the batteries if the display
becomes unclear.
j
Remove the battery compartment cover on
the back of the weather station.
j
Remove the used batteries.
j
Insert 3 new batteries type AA 1.5 V
(Mignon, LR06).
note: Make sure you fit the batteries the
right way round (polarity). The correct polarity
is shown inside the battery compartment
j
Close the battery compartment
j
Press the RESET button
light up briefly.
Outdoor sensor:
note: For this step you need a flat-blade
screwdriver.
j
Open the battery compartment cover on the
rear of the outdoor sensor by turning the
screw in an anticlockwise direction with the
flat-blade screwdriver.
j
Remove the used batteries.
j
Insert 2 new batteries of type AAA 1.5 V
(Micro, LR03).
note: Ensure the correct polarity. This is
shown in the battery compartment
j
Close the battery compartment cover and
tighten the screw in a clockwise direction.

Troubleshooting

Q 
note: This appliance has delicate electronic
components. This means that if it is placed near
an object that transmits radio signals, it could
cause interference. This could be, for example,
mobile telephones, walkie talkies, CB radios,
remote controls and microwaves.
j
If the display indicates a problem, move such
objects away from it or remove the batteries
for a short while and then replace them.
. The
12
appears in the
23
.
34
.
34
. All the symbols
33
.
40