Energy Saving Mode - Bosch Indego 350 Originalbetriebsanleitung

24 | English
Symbol Meaning
➑ 1 2 3 Garden number (shown when more than
one garden map is in the mower memory)
The display switches into sleep mode, if no input is made for
10 minutes.
Adding a Further Garden/Lawn Area
(see figure I)
To install an additional lawn area, please follow the instruc-
tions in the Installation Guide.
With separate docking station, separate gardens (see
figure I, right): The mower can be used on up to three dif-
ferent gardens. For an additional garden, a separate docking
station (see figure A) and the necessary perimeter wire and
pegs are required. If a schedule or the „Bosch AUTO" calen-
dar function is selected it will cut the grass of the area is in,
within the time slots.
Switch off the mower when transporting it between different
gardens.
Note: software updates have to be carried out on the mower
in every docking station.
To ensure remembering which docking station belongs to
which garden, it is recommended to label the docking sta-
tions with the garden number and description when storing
them for winter.
Without separate docking station: It is possible to connect
the lawn areas by placing the perimeter wire between the
two lawn areas parallel to each other as close as possible
(see figure I, top left). The additional lawn area without
docking station is not recorded in the map memory and the
mower will not use the LogiCut cutting strategy in this lawn
area without the docking station. The maximum recommen-
ded lawn area without a docking station is 40 m
will mow until it runs out of battery and will need to be car-
ried back to the docking station for charging.
Mowing
Do not let children ride the mower.
u
Press the stop button on top of the mower before lift-
u
ing. Always lift the mower by its handle. (see figure F)
Make sure the cutting area is free of small animals such as
hedgehogs or tortoises.
After successful installation you can either immediately be-
gin to mow by confirming "Mow now" on the display, or
wait for the next scheduled cutting period, as programmed
by the Bosch AUTO Calendar Function (previous setting re-
quired).
A mowing schedule can also be set up according to your
needs.
The mower must mow a lawn area 3 times completely (do 3
full cuts) to learn the lawn area. During the learning phase,
the visual result may not be optimal.
Approximate runtimes for complete garden coverage using
LogiCut are listed below. Please note that the run times will
F 016 L81 848 | (01.10.2018)
vary depending on the lawn complexity and number of ob-
jects within the garden.
2
100 m
2
350 m
2
400 m
Set a schedule with frequent repetitions. For best mowing
results, set up a frequent mowing schedule for longer lasting
battery and for preventing debris on the lawn.
When the mower is mowing
In „manual" mode, the mower works until the lawn is
mowed. Mowing is interrupted only for charging the battery.
When the lawn area is mowed, the mower returns to the
docking station.
In the programmable „Schedule" mode or with the "Bosch
AUTO" calendar function, the mower operates continuously
for a set period of time. Mowing is interrupted only for char-
ging the battery. If the lawn area is mowed before the end of
a time slot, the mower returns to the docking station.
To stop mowing prematurely, press the Stop button or send
the mower back to the docking station by pressing the con-
firm button ✓.

Energy saving mode

The mower reduces its energy consumption by automatically
switching off the power to the perimeter wire when it is not
mowing and not being charged.
To wake up the mower manually from the energy saving
mode, press the confirm button ✓ and afterwards select
either "Mow now" or another "Mowing mode", while the
mower is in the docking station.
When a schedule or the AUTO Calendar Function becomes
active, the wire signal will start up automatically.
2
. The mower
Mowing small lawn areas with "SpotMow"
SpotMow is intended for mowing small areas that require
special treatment without having to mow the whole lawn,
such as the area under a piece of garden furniture that has
been removed. The mower is to be positioned at the lower
left corner of the intended area to mow. (see figure H). The
finally mowed area depends on the lawn conditions; it will
not necessarily be an exact square. After completion of
"SpotMow", follow the instructions on the screen.
Note: For safety reasons, "SpotMow" cannot be used outside
the perimeter wire.
Sensors
The mower is equipped with the following sensors:
– The lift-up sensor is activated when the mower is lifted.
– The rollover sensor detects when the mower tips over.
– The tilt sensor is activated when the mower reaches a
slope angle of 32°.
When one of the sensors is activated, e.g. the lift-up sensor,
the drive motors and cutting blades are stopped. A message
is indicated in the display, e.g. "lift-up".
4 h
12 h
14 h
Bosch Power Tools