Nice HSCU2 series Anweisungen Und Hinweise Für Die Installation Seite 37

1 - SYSTEM ARMING AND DISARMING
1.1 - Via remote control
ARMING: Press key
associated with the remote control .
PARTIAL ARMING 1: Press key
only the zones associated with the "Partial 1" command .
PARTIAL ARMING 2 (if configured, contact the installer if necessary): Press
key ; the control panel arms only the zones associated with the "Partial 2"
command .
In both cases the remote control communicates with the control panel
with its flashing orange led. The control panel confirms system arming
by turning the green led on the remote control on.
If any notifications or open fixtures are present, indicated by
screen will display the list of messages . Select one and in the next page select:
- ARM and confirm with to force arming .
- CANCEL and confirm with
Close the open fixtures and check the events log . If the message persist, con-
tact the installer .
If the system does not arm, check the touch screen for messages (
or open fixtures, solve the outstanding problems and arm the system with the
remote control . Alternatively, use the touch screen to force system arming .
DISARMING: Press . The remote control communicates with the con-
trol panel via the orange flashing LED . The control panel confirms the system
disarming visible on the remote control with the green fixed LED . The system
deactivates only the zones associated with the remote control .
1.2 - With the touch screen keypad
ARMING: Turn the touch screen on and press
In the next screen press the icon
Enter the access code and confirm with
Confirm once again with
code or click on the zones you wish to exclude and then confirm with
The control panel confirms the system arming, visible through a specific mes-
sage on the display . Also the time available to exit without causing an acciden-
tal alarm is displayed .
If any notifications or open fixtures are present, indicated by
screen will display the list of messages . Select one and in the next page select:
- ARM and confirm with to force arming .
Operation manual
(to be given to the final user)
; the control panel arms all zones
; the control panel arms
to quit without arming .
.
to arm all zones associated with the access
- CANCEL and confirm with
Close the open fixtures and check the events log . If the message persist, con-
tact the installer .
DISARMING: Turn the touch screen on and press the icon
In the next screen press the icon
Enter the access code and confirm with
The control panel confirms the system disarming, visible through a specific
message on the display . The system deactivates only the zones associated
with the access code .
The touch screen display shows the system status and the activated zones .
1.3 - With the transponder key
If a touch screen keypad is installed in the system, the system can be armed
, the touch
and disarmed through the special transponder key so as to avoid the activation
of the access code .
The transponder key reader is active whenever the touch
screen is turned on; this is shown with the
tion is only active if at least one transponder key has been
associated with the control panel) .
symbol)
ARMING: Turn the touch screen on and
move the transponder key near the bottom
left corner of the touch screen . A beep is
emitted to confirm system arming .
If the icon is not visible, press icon
Scroll down the window and activate the
reading of the transponder keys by selecting
the icon
The key reader active icon
the bottom line .
If the icon is not visible press the icon once
again .
If any notifications or open fixtures are pre-
sent, indicated by
display the list of messages . Select one and
in the next page select:
- ARM and confirm with
arming .
- CANCEL and confirm with
Close the open fixtures and check the events log . If the message persist, con-
tact the installer .
DISARMING: proceed as for "arming"; when the system is armed, reading the
key anew disarms the associated zones .
1.4 - System status display
When the touch screen is on, the individual armed zones can be displayed in
the main page .
system disarmed
zone A armed
The main screen also provides information on:
•
GSM signal level
No GSM coverage
•
Touch screen battery level
Battery charged
.
The image indicates an important message. Check the event list
and contact the installer if the message persists.
The images and
, the touch
the anomaly persists .
to quit without arming .
displays in
, the touch screen will
to force
to quit without arming .
system armed
zone B armed . . . .
Excellent GSM coverage
Battery completely discharged
refer to system malfunctions . Contact the installer if
icon (the func-
English – 35