Installation; Operation - Scheppach ASP30 Original Bedienungsanleitung

6. Installation

Installing the front wheels
1. Open the quick coupling (Fig. 1 / Pos. 8) on both
sides of the device and remove the machine head.
2. Put the water tank (Fig. 1 / Pos. 11) on the head.
3. Push the front wheels (Fig. 2 / Pos. 10) into the two
openings on the bottom of the device.
Installing and removing the dust bag
1. Push the clip back and pull the handle up. (Fig. 3)
2. Push the slider back. (Fig. 4)
3. Put the dust bag (Fig. 5 / Pos. 25) on the connec-
tion.
4. Release the slider. (Fig. 6)
3 filter system (Fig. 7)
Filter 1 – Coarse dust is caught by the dust bag.
Filter 2 – The dust is bound in water
Fill the water tank (Fig. 1 / Pos. 11) up to the mark.
Filter 3 – The HEPA filter (Fig. 1 / Pos. 21) filters fine
dust.
Inserting the filter
1. Release the quick coupling (Fig. 1 / Pos. 8) on both
sides of the device.
2. Push the selected filter in on the bottom of the ma-
chine head until it locks in place. (Fig. 8)
• Foam filter (Fig. 1 / Pos. 20): suitable for wet
vacuuming
• HEPA filter (Fig.1/Pos.21):
vacuuming
Installing the hose
Dry vacuuming:
1. Insert the HEPA filter (Fig. 1 / Pos. 21).
2. Push the vacuum hose (3) onto the vacuum nozzle
(3) and turn this clockwise. (Fig. 1)
3. Insert the cover for the hose connection (13) into
the wet vacuuming connection. (Fig. 9).
Wet vacuuming:
1. Insert the foam filter (Fig. 1 / Pos. 21).
2. Push the vacuum hose (2) into the connection on
the water tank (11) and turn this clockwise.
3. Insert the hose connection cover (Fig. 1 / 13) into
the dry vacuuming connection
Air blasting
1. Ensure that the water tank (Fig. 1 / Pos. 11) is com-
pletely drained and clean.
2. Push the vacuum hose (Fig. 1 / Pos. 2) into the blast
nozzle (Fig. 1 / Pos. 16) and turn this clockwise
Extraction unit for electrical devices
1. Connect the dust extraction unit (Fig. 1 / Pos. 22) to
the electrical device and the vacuum hose (Fig. 1 /
Pos. 2).
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
suitable for dry
2. Push the vacuum hose (Fig. 1 / Pos. 2) onto the
vacuum nozzle (Fig. 1 / Pos. 3).
3. Plug the electrical device's plug into the socket
(Fig.1 / Pos. 7).
Assembling accessories
1. After connecting the vacuum hose (Fig. 1 / Pos. 2),
push the handle (Fig. 1 / Pos. 19) into the telescopic
vacuum pipe (Fig. 1 / Pos. 14).
2. Press the unlock button for the telescopic vacuum
pipe (Fig. 1 / Pos. 17) to extend the telescopic vac-
uum pipe (Fig. 1 / Pos. 14).
Installing brushes and nozzles
1. Select the brush or nozzle suitable for the relevant
job.
2. Push the telescopic vacuum pipe (Fig. 1 / Pos. 14)
into the required brush or nozzle.
Floor nozzle (Fig. 10) – to vacuum carpets (setting
A) and hard surfaces (setting B). Also suitable for wet
vacuuming.
Joint nozzle (Fig. 1 / Pos. 23) – for locations that are
difficult to access, e.g. edges, radiators.
Brush nozzle (Fig. 1 / Pos. 24) – to remove dust
from highly sensitive pieces of furniture or items sus-
ceptible to scratching.

7. Operation

Switching on:
Tip the on/off switch (Fig. 1 / Pos. 15) into the ─
position to switch the device on.
Switching off:
Tip the on/off switch (Fig. 1 / Pos. 15) into the 0 posi-
tion to switch the device off.
Switching on with an electrical device connected:
Tip the on/off switch (Fig. 1 / Pos. 15) into the ═ posi-
tion to switch the device and the connected electrical
device on.
Speed regulation:
The vacuuming force can be adjusted using speed
regulation (Fig. 1 / Pos. 5).
• Turn speed regulation clockwise to increase the
speed and suction force.
• Turn speed regulation anticlockwise to reduce the
speed and suction force.
GB | 17