Skil 2050 Originalbetriebsanleitung Seite 7

e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fi re when used with
another battery pack.
b) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fi re.
c) When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fi re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR CORDLESS SEALANT
GUNS
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the charger
(chargers with a rating of 230V or 240V can also be
connected to a 220V supply)
• In case of electrical or mechanical malfunction,
immediately switch off the tool or unplug charger from
power source
• SKIL can assure fl awless functioning of the tool only
when original accessories are used
• The tool/charger is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the tool/charger by a
person responsible for their safety
• Ensure that children do not play with the tool/charger
CHARGING/BATTERIES
• Charge battery only with the charger that is supplied
with the tool
• Do not touch the contacts in the charger
• Do not charge battery in damp or wet environments
• Do not expose tool/charger/battery to rain
• Store tool/charger/battery in locations where
temperature will not exceed 40°C or drop below 0°C
• Batteries will explode when disposed of in fi re, so do
not burn battery for any reason
• Do not use charger when damaged; take it to one of the
offi cially registered SKIL Service Stations for a safety
check
• Do not use charger when cord or plug is damaged; cord
or plug should be replaced immediately at one of the
offi cially registered SKIL Service Stations
• Do not use battery when damaged; it should be
replaced immediately
• Do not disassemble charger or battery
• Do not attempt to recharge non-rechargeable batteries
with the charger
• Explanation of symbols on charger/battery
4 Only use the charger indoors
5 Double insulation (no earth wire required)
6 Fail-safe isolating transformer (the power source is
electrically separated from the transformer output)
7 Automatic shut-off when charger gets too hot
(thermic fuse blows and charger becomes useless)
8 Incorrect polarity of the charger connection could
cause a hazard (only charge the battery with the
charger supplied)
9 Do not dispose of the charger together with
household waste material
0 Do not dispose of the battery together with
household waste material
! NiMH technology provides more energy in a less
environment-polluting way
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of the charger to the earth terminal of the
plug
• If for any reason the old plug is cut off the cord of the
charger, it must be disposed of safely and not left
unattended
USE
• Charging battery @
- battery of new tools is not fully charged
! remove battery from charger after charging
period has ended thereby lengthening the service
life of the battery
IMPORTANT:
- after 3 hours the charging operation will be
completed, and the battery may be used, even
though the red light may still be on (the red light
may require more than 3 hours to turn off)
- while charging, the charger and the battery may
become warm to touch; this is normal and does not
indicate a problem
- ensure that the outside surface of the battery is clean
and dry before inserting into charger
- do not charge at temperatures below 0°C and over
40°C; this will seriously damage the battery as well
as the charger
7