Ryobi RLM1956MEB Originalanleitung Seite 8

2. Remove the hub cap.
3. Remove the nut from the wheel axle, then remove the
wheel.
4. Replace with new wheel and reinstall nut to secure.
CLEANING THE AIR FILTER
See fi gure 8.
For proper performance and long life, keep the air fi lter
clean.
1. Remove the air fi lter cover by pushing down the latch
while gently pulling out the cover.
2. Remove the air fi lter and clean it in warm soapy water.
Rinse and let dry completely.
3. Apply a light coat of engine oil to the air fi lter, then
squeeze it out using an absorbent cloth or paper towel.
4. Reinstall the air fi lter into the air fi lter base.
5. Replace and secure the air fi lter cover.
NOTE: The filter should be replaced annually for best
performance.
WARNING
A leaking fuel cap is a fi re hazard and must be replaced
immediately.
The fuel cap contains a non-serviceable fi lter and a
check valve. A clogged fuel cap will cause poor engine
performance. If performance improves when the fuel
cap is loosened, check valve may be faulty or clogged.
Replace fuel cap if required.
CHANGING THE ENGINE OIL
See fi gure 8.
Engine oil should be changed after every 25 hours of use.
Change the oil while the engine oil is still warm, but not hot.
This allows the oil to drain quickly and completely.
1. Remove the oil fi ll cap/dipstick.
2. Tip mower onto its side and allow oil to drain from the oil
fi ll hole into an approved container.
3. Place mower upright and refi ll with oil.
NOTE: Used oil should be disposed of at an approved
disposal site. See your local oil retailer for more
information.
MAINTAINING THE SPARK PLUG
See fi gure 7.
The spark plug must be properly gapped and free of
deposits in order to ensure proper engine operation. To
check:
1. Remove spark plug boot.
2. Clean any dirt from around base of spark plug.
3. Remove spark plug using a 13/16 in. spark plug socket
(not provided).
4. Inspect spark plug for damage, and clean with a wire
brush before reinstalling. If insulator is cracked or
chipped, spark plug should be replaced.
NOTE: If replacing, use the following recommended
6
plugs are Torch E7RTC is NGK BPR6HS.
5. Measure plug gap. The correct gap is 0.028 − 0.031 in.
To widen gap, if necessary, carefully bend the ground
(top) electrode. To lessen gap, gently tap ground
electrode on a hard surface.
6. Seat spark plug in position; thread in by hand to prevent
cross-threading.
7. Tighten with wrench to compress washer. If spark plug
is new, use 1/2 turn to compress washer appropriate
amount. If reusing old spark plug, use 1/8 to 1/4 turn for
proper washer compression.
NOTE: An improperly tightened spark plug will become
very hot and could damage the engine.
8. Reinstall spark plug boot.
STORING THE PRODUCT
When storing the mower for 30 days or more:
■ If using fuel stabilizer, follow stabilizer manufacturer's
directions to add stabilizer to petrol in fuel tank. Run
engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor.
WARNING
Do not store the lawn mower with petrol in the tank
inside a building where fumes may reach an open fl ame
or spark.
■ If not using fuel stabilizer, allow the engine to run until
the mower is completely out of petrol.
■ Once the engine has stopped, allow the blade to come
to a complete stop and disconnect the spark plug wire.
■ Turn the fuel valve to the closed position.
■ Turn mower on its side (with carburetor facing up) and
clean grass clippings that have accumulated on the
underside of the mower deck.
■ Clean the underside of the mower deck.
■ Wipe the mower clean with a dry cloth.
■ Check all nuts, bolts, knobs, screws, fasteners, etc., for
tightness.
■ Inspect moving parts for damage, breakage, and wear.
Have repairs made on any damaged or missing parts.
■ Store the mower in a well-ventilated area that is clean,
dry, and out of the reach of children.
■ Do not store near corrosive materials such as fertilizer
or rock salt.
To lower the handle before storing:
■ Loosen the starter rope guide knob. Remove starter
rope from guide and allow to retract into engine.
■ Fully loosen the handle knobs on the sides of the
handle and fold the upper handle down.
■ Unscrew the lower handle lock nuts.
■ Fold the lower handle forward, making sure not to bend
or kink the control cables.
English