Start-Up Instructions - Jacuzzi J-470 Montageanweisung Und Bedienung Und Wartung

6
7
12
2
6
5
Remove the access door on the controller.
Locate the gray Terminal, towards the top of the controller,.
Grab one of the white levers. Push the lever upward to the open
position. If opened correctly the lever will stay in place and remain
open.
You will notice that lifting the lever opens the slot for the power
wire. Insert the power wire into slot A as shown. Then put down
the white lever and secure wire in place. Gently pull on wire after
installation to verify it is clamped tightly into terminal.

Start-Up Instructions

Read each step in its entirety before proceeding with
that step.
I
Remove any dirt from the spa. Although the spa shell has
been polished at the factory, you may want to treat it with a spe-
cially formulated spa cleaner and wax available from your dealer
prior to filling the first time.
I
Filling the Spa
Remove the filter cover, then remove both filter cartridges as out-
lined in section "Cleaning The Filters".
Place the end of your garden hose into empty skimming filter bucket
(filter bucket on your left) as you stand next to the spa. Fill spa half
way, then place the garden hose into the opposite filter bucket (fil-
ter bucket on your right) while adding the remaining fill water.
Fill spa until water level is above all jets and just touching the
bottom of each headrest in its lowest position.
Do not overfill your mini-pool.
N.B.: If your water is extremely hard, it is preferable to fill halfway
with hard water and the rest of the way with softened water. Or, you
may fill entirely with hard water if you use a special water additive.
Always fill the spa from both filter connections, so as to expel
air trapped in the pumps. Otherwise the air may remain trapped,
preventing the pumps from circulating the water.
After filling, make sure both filters are installed properly before
applying power to the spa. (refer to sec. "Cleaning The Filters").
I
Checks
Open the cabinet access panel and check all pump fittings to make sure
they are tight. Loosening can occur during shipping and handling.
11
Access Door
WARNING!
DONOT LOOK AT LIT BULB
SEVERE EYE DAMAGE
OR BLINDNESS CAN OCCUR
9
1
8
4
10
3
10 Electronic Ballast (For CLEARRAY System)
2
11 Display
6
12 QuickDrain™
I
Turn on Power
Turn on power to spa from the main switch (refer to the chap-
ter "Electrical safety". The heater and circulation pump will auto-
matically activate.
The flashing of the water temperature icon together with "COOL"
or "ICE" on the display of the control panel may be normal as
the water in the system is often cold; please refer to the "Prob-
lem resolving - Display messages" section.
I
Startup
Start up the pumps (refer to "Control panel" chapter).
I
Addition of chemcial additives at first start-up
Add the spa water chemicals as recommended by your dealer (refer
to the chapter "Water Quality Maintenance" for general guidance).
WARNING!
Do not get in the spa until the quantity of disinfectant
has not dropped below the level recommended by the
manufacturer and/or by your retailer.
I
Water heating
The water can be heated once the parameters of the chemical
additives have reached the correct value: use the circular key-
pad to either increase or decrease the temperature.
up
left
I
The heater will be turned off when the temperature has ex-
ceeded the temperature set by 1 degree and will be reactivated
when the temperature descends 1 degree below that set.
Heater characteristics:
- The maximum temperature that may be set is 40 °C, the mi-
nimum is 27 °C.
- If the spa is supplied according to the minimum electric current
absorption configuration (see pre-installation sheet) turn the
pump off to activate the heater.
- Setting the temperature at maximum only results in a higher end
temperature and will not accelerate the heating process itself.
48
1 Electrical box
2 Power supply entrance(s)
3 Pump1
4 Heater
5 Drain valve
6 Pump drain plug(s)
7 Pump 2
8 Circulaiton pump
9 CLEARRAY Water Purification System
right
down