Before Use; Safety Measures When Handling The Cutting Blade; Initial Operation; Assembly - FLORABEST FBS 43 B2 Originalbetriebsanleitung

WARNING!
■ Petrol is highly fl ammable. Only store petrol in the containers
provided.
■ Only refuel out in the open and do not smoke.
■ The fi ller cap must not be opened and refuelling must not take
place while the engine is running or when the device is hot.
■ Do not attempt to start the engine if the petrol has overfl owed.
Instead, remove the device from the area polluted by petrol. Do not
attempt to restart the device until the petrol fumes have dissipated.
■ For reasons of safety, the petrol tank and fi ller cap must be replaced
if they are damaged.

Before use

IMPORTANT!
■ When mowing/trimming, always wear non-slip safety boots and
proper safety clothing, such as work gloves, a protective helmet,
a protective mask or protective glasses and hearing protection.
■ Check the area in which the device is to be used and remove any
objects that may be caught and slung away.
■ Before use and after dropping or other impacts, always visually
inspect the device to check whether the cutting tool, mounting bolts
and the entire cutting unit is damaged. Worn or damaged cutting
tools and mounting bolts must be replaced.
■ Always perform a visual inspection prior to use to check whether
the cutting tool is worn or damaged. To prevent imbalance, worn or
damaged cutting tools and mounting bolts may only be replaced in
sets.
Limit the noise development and vibrations to a minimum!
■ Only use devices that are in good condition.
■ Maintain and clean the device on a regular basis.
■ Adapt your working method to the device.
■ Do not overload the device.
■ Have the device inspected if necessary.
■ Switch the device off when not in use.
■ Wear gloves.

Safety measures when handling the cutting blade

■ The device may cause blindness and injuries to bystanders. Maintain a
minimum distance of 15 metres in all directions between the device and
other persons or animals.
■ Do not use the device if any of the cutting blade accessories have not
been properly installed.
■ The cutting blade can be catapulted away from objects with force.
This can lead to arm or leg injuries. If the device comes into contact
with a foreign body, immediately shut down the engine and wait until
the cutting blade has come to a complete stop. Check the cutting blade
for damage. Always replace the cutting blade if it is bent or torn.
■ The cutting blade forcefully slings away objects as well as soil. This may
cause blindness or injuries. Wear eye, face and leg protection. Always
remove objects from the work area before using the cutting blade.
FBS 43 B2
■ The cutting blade continues to run down once the throttle lever has
been released. A cutting blade that is running down to a stop may
cause cutting injuries to you or bystanders. Turn the engine off and
make sure that the cutting blade has come to a complete stop before
performing any work on the cutting blade.

Initial operation

Assembly

Assembling the guide handle (Fig. 3a - 3c)
■ Assemble the guide handle
handle must be installed as displayed in fi gures 3a - 3c. Only tighten
the handle screw once you have adjusted the shoulder strap
optimal operating position (see "Putting on the shoulder strap/adjusting
the cutting height" chapter).
■ To adjust the guide handle the correct distance from the body and to
ensure that there is suffi cient distance between the engine and yourself,
loosen the two screws on the underside of the guide handle
fi g. 8j).
Assembling the guide rail (4a - 4c)
■ Press the locking lever and slide the guide rail
the guide rail connecting piece
the guide rail slide into each other, lightly turn the line spool
cutting blade / if necessary. The locking lever hook
with the slot . Tighten the handle screw
Assembling the cutting blade protective hood
WARNING!
■ The cutting blade protective hood
with the cutting blade. The cutting blade protective hood
to the guide rail using 2 screws
Installing/replacing the cutting blade
■ Install/replace the cutting blade
■ Lock the cutting blade / to the drive plate (see fi g. 6c).
■ Insert the pressure plate via the splined shaft thread (see fi g. 6d).
■ Attach the pressure plate cover
■ Locate the drive plate drill hole, align with the underlying groove and
lock with the enclosed hexagonal key
the spark plug spanner (see fi g. 6f + 6g).
NOTE! Left-hand thread!
■ The cutting blades / are delivered with plastic protective caps.
These must be removed prior to use and reattached when not in use.
IMPORTANT! SHARP EDGES, WEAR PROTECTIVE GLOVES
■ ATTENTION! Assemble the cutting line protective hood
cutting blade protective hood
■ The cutting line protective hood
with the cutting line. The cutting line protective hood
displayed in fi gure 7a.
■ Ensure that the cutting line protective hood
A blade is located on the inner side of the cutting line protective
hood (see fi g. 7a). This is covered with a protective sleeve
fi g. 7a).
■ Remove the protective sleeve
completing your activities.
as shown in fi gures 3a - 3c. The guide
(see
(see fi g. 4a) into
. Make sure that the drive shafts inside
must engage
as displayed in fi gure 4c.
must be assembled when working
is attached
as displayed in fi gure 5.
/ as displayed in fi gures 6a - 6g.
(see fi g. 6e).
, now tighten the nut
on the
.
must be assembled when working
is assembled as
is correctly engaged.
before starting work and reattach after
GB
to the
/the
with
(see
5