Troubleshooting - Geneva Model L Bedienungsanleitung

USING THE DEVICE
BLUETOOTH
Mobile phones and computers with Bluetooth can
connect to the Model l/Xl and play music. The mobile
phone or computer must support Bluetooth A2dP.
Initial Setup ( "Pairing" ) with iPhone
®
1. Press the key on the remote control. Wait for 20
seconds until the display shows a blinking "Pairing".
2. Select "Settings" on your iPhone . Select "General
®
/ Bluetooth". Turn on Bluetooth. New Bluetooth
devices are discovered automatically. After a few
seconds "GENEVA L ( Not Paired )" will appear.
3. Select "GeNeVA l". The phone is now connected
( "Pairing" ) to the Model L.
4. If the phone asks for a PIN: enter "0000" ( four zeros ).
5. Now you can play music on an iPhone and listen
®
to it on the Model l.
Pairing guides for other devices and mobile phones
Go to www.genevalab.com and select "Support."
Bluetooth settings on the iPhone
®
Settings on iPhone Playing
®
Playing Music
Most phones connect automatically to the Model
L / XL after the initial setup ( "Pairing" ).
1. Press the key on the remote control. While the
Model l / Xl connects, the display shows "Con-
nect" for a few seconds.
2. Now the music that is playing on your mobile phone
will automatically be streamed to the Model l / Xl.
3. Change tracks with and .
High quality Bluetooth audio with aptX and
AAC codecs
Some mobile phones support a higher transmission
quality than the standard Bluetooth codec ( SBC ).
Model l / Xl supports the high quality codecs aptX
and AAC. The Model l / Xl will automatically select
the high quality Bluetooth aptX or AAC codecs, if the
mobile phone supports this feature.
Status information on the display
"Search": Searching previously paired devices.
"Connect": Connection successful.
"Pairing": If the Model l / Xl did not make a success-
ful connection within 20 seconds, the Model l / Xl will
go into the pairing mode for 2 minutes.
"Connected to XXX": Successfully connected to
device with the name XXX.
"BLUE C": A device is connected.
"BLUE —": No device is connected.
LINE - IN
The Model l / Xl has two line-in inputs for external
audio devices:
• RCA connectors ( "Line-In" )
• 3.5mm connector ( "Air" ) with automatic
power-on functionality
1. Connect one end of a line-In cable to the line-In
or Air connector on the bottom panel of Model
L / XL ( RCA connectors ), then connect the other
end of the cable to the audio device ( headphone or
Line-Out connector ).
2. Press the LINE-IN or AIR key on the remote control.
AUTOMATIC POWERING ON AND OFF
Powering On with the AIR connector
If an external audio device has its audio output
connected to the AIR connector, Model l / Xl will
automatically power itself on, as soon there is an
audio signal on the AIR connector. The AIR connector
is suited for network audio streaming devices, such
as the Apple AirPort Express ( AirPlay ) and Sonos
products. When you turn on a streaming device, it will
automatically turn on the Model l / Xl.
Powering Off with the energy saving function
The Model l / Xl will automatically turn itself off after
15 minutes if there is no active Bluetooth connection,
no is Cd playing, or if there is no audio signal at line-
in/AIR connectors.
4

TROUBLESHOOTING

The Model L/XL does not turn on when I touch the
button.
Touch button with one finger only. Don't touch the
rest of the touch panel with other fingers. The touch
panel works properly when used with one finger only.
Why is the Model L/XL turning itself off?
The energy saving function turns the Model l/Xl
automatically off. The Model l/Xl will automatically
turn itself off after 15 minutes if there is no active
Bluetooth connection, no Cd is playing or if there is
no signal at the line-in inputs. When this happens,
the display shows "eCo oFF".
Why is my mobile phone not connecting?
Please check the Support pages at genevalab.com.
How do I reset Bluetooth?
Up to three paired Bluetooth devices can be stored.
To clear the memory, perform the following steps:
1. Select Bluetooth on Model l/Xl.
2. Within 5 seconds of entering Bluetooth mode, hold
until "ReSeT" displays.
3. Pair your mobile phone again.
What is the PIN for a Bluetooth connection?
The PIN is: 0000 ( 4 zeros ). Not all computers
or mobile phones require a pin code during initial
setup ( Pairing ).
I have an unreliable connection with dropouts
when listening via Bluetooth.
• Move the mobile phone closer to the Model l/Xl.
• Move away or turn off other wireless devices that
can disturb a Bluetooth connection ( for example
WLAN / Wi-Fi, other mobile phones etc. ).
The FM automatic search does not find all stations.
The FM automatic search function ( hold or keys )
finds only stations with a strong signal.
How do I erase or overwrite a preset?
Stored presets do not need to be erased — just use
the steps to store a new station in a preset.
I cannot turn off the device, the display shows "Air
active — cannot turn off".
There is still an audio signal on the Air connector.
either stop the audio source or disconnect the exter-
nal device from the AIR connector.
How can I verify that the remote control works?
every time a key is pressed on the remote control, a
small red light on the display lights up briefly.
English
How can I change the remote control battery?
1. Push the small lever in the direction of the arrow
with your finger or a small screwdriver.
2. While holding the small lever, slide out the battery
compartment.
3. Replace the battery ( 3V lithium cell, 3V CR2032 ).
Verify that the battery is inserted with the right
polarity.
3
1 2
How is it possible to hear in stereo from only
one speaker?
Inside the wood cabinet there are two ( Model L ) or
four ( Model XL ) acoustic chambers, for the left and
right channels. Using the embracingSound ® algo-
rithm Model l/Xl creates a real stereo reproduction
with two acoustic chambers that are very close to
each other.
How do I clean the device?
Use a soft, dry cloth to avoid making scratches on
the surface. do not use cleaning alcohol, or other
solvent fluids to clean the surface of the Cabinet as
this can both damage the lacquer and also cause
electrical failures. Before cleaning, unplug the device
from the AC power outlet.
SUPPORT
More information and additional troubleshooting
Check the "Support" pages at genevalab.com.
Service and repair
If the product is damaged and needs repair, please
contact your dealer. Visit genevalab.com to find a
dealer in your area.
Warranty
See the specific terms for your country at genevalab.com.
Geneva ® is a registered trademark of G-lab GmbH.
Apple, iPod, iPhone and iPad are trademarks of Apple Computer, Inc.
registered in the U.S. and other countries.
The embracingSound ® trademark is owned by embracing Sound
experience AB.
The Bluetooth word mark and logos are registered Trademarks owned by
®
Bluetooth SIG, Inc.
aptX is a trademark of CSR plc.
© 2013 G-lab GmbH. Manual for Geneva Sound System, Model l/Xl,
Version v1.2
5