Option1 Settings Menu; Setting The On-Screen Display; Setting The Pc2/Component2 Connectors; Setting The Pc1 Connector - Pioneer PDP-42MVE1 Bedienungsanleitung

Option1 Settings Menu

Setting the on-screen display

This sets the position of the menu, the display format
(horizontal or vertical) etc.
Example: Turning the DISPLAY OSD off
On "OPTION1" menu, select "OSD", then press the MENU/
SET button.
The "OSD" menu appears.
On "DISPLAY OSD" of "OSD" menu, select "OFF".
OSD
DISPLAY OSD
OSD ADJUST
OSD ANGLE
OSD ORBITER
OSD CONTRAST
SEL. ADJ.
Information
DISPLAY OSD settings
ON: The informations on screen size, volume control,
etc. will be shown.
OFF: The informations on screen size, volume control,
etc. will not be shown.
The DISPLAY button on the remote control will not
function either.
OSD ADJUST settings
Adjusts the position of the menu when it appears on
the screen.
The position can be set between 1 to 6.
OSD ANGLE settings
Sets the display format (landscape "H" or portrait "V").
When the unit is installed vertically set the OSD
ANGLE at "V".
"H"
OPTION1 1 / 3
OSD
BNC INPUT : RGB
D-SUB INPUT : RGB
RGB SELECT : AUTO
HD SELECT : 1080B
INPUT SKIP : OFF
ALL RESET : OFF
NEXT PAGE
SEL. MENU OK EXIT RETURN
OSD ORBITER settings
ON: The position of the menu will be shifted by eight
dots each time OSD is displayed.
OFF: OSD will be displayed at the same position.
OSD CONTRAST settings
NORMAL: OSD brightness is set to normal.
LOW: OSD brightness is set to lower.
: OFF
: 1
: H
: OFF
: LOW
EXIT RETURN
"V"
OPTION1
OSD
BNC INPUT
: RGB
D-SUB INPUT
: RGB
RGB SELECT
: AUTO
HD SELECT
: 1080B
INPUT SKIP
: OFF
ALL RESET
: OFF
1024 768
SEL. MENU OK
EXIT RETURN

Setting the PC2/COMPONENT2 connectors

Select whether to set the PC2/COMPONENT2 to RGB,
component or SCART1, 2.
Example: Set the BNC INPUT mode to "COMP."
On "BNC INPUT" of "OPTION1" menu, select "COMP.".
OPTION1
OSD
BNC INPUT
D-SUB INPUT
RGB SELECT
HD SELECT
INPUT SKIP
ALL RESET
NEXT PAGE
SEL. ADJ.
Information
BNC INPUT Settings
RGB: Use the 5BNC terminals for HD, VD and RGB
signals.
COMPONENT: Use the 3BNC terminals for
component signals.
SCART1: Use the 4BNC terminals for RGB with
composite sync. See page 6.
SCART2: Use the 3BNC terminals for RGB and the
VIDEO1 terminal for composite sync. See page 6.

Setting the PC1 connector

Select one of the signals being transmitted to the PC1
terminal.
Example: Set the D-SUB INPUT mode to "SCART3"
On "D-SUB INPUT" of "OPTION1" menu, select
"SCART3".
OPTION1
OSD
BNC INPUT
D-SUB INPUT
RGB SELECT
HD SELECT
INPUT SKIP
ALL RESET
NEXT PAGE
SEL. ADJ.
Information
D-SUB INPUT Settings
RGB: Use the D-SUB terminal for RGB signals.
SCART3: Use the D-SUB terminal for RGB signal fed
from SCART. See page 6.
1 / 3
: COMP.
: RGB
: AUTO
: 1080B
: OFF
: OFF
EXIT RETURN
1 / 3
: RGB
: SCART3
: AUTO
: 1080B
: OFF
: OFF
EXIT RETURN
17
En