Replay; Storage Locations M1 - M6; Immediate Replay; Calling Up A Message By Remote Control - Monacor PA-1120DMT Bedienungsanleitung

6.2 Replay

Use the control LEVEL (16) to adjust the volume of
the messages replayed. Prior to the first message
replay, turn the control approx. to mid-position and,
if required, adjust the control during replay. If the
volume of the insertion module is too low for the
amplifier used even though the control has been
turned to the right stop, the output level may be
increased by another 10 dB (
If an emergency message is to be replayed
automatically, make absolutely sure to prevent any
inadvertent readjustment of the control.
Headphones can be used to monitor a stored
message: Connect the headphones (minimum
impedance: 64 Ω) to the jack PHONES (3) [mono,
only the left side for stereo headphones]; the output
(25) to the amplifier will be muted.
6.2.1 Storage locations M1 – M6
The following description applies to the normal
replay mode. Please refer to chapter 6.2.1.1 for the
immediate replay mode.
For one-time replay of a message that has been
recorded on one of the storage locations "M1" to
"M6":
1) Press the button (15) of the storage location
desired. The display will show, for example:
M3 Rep2
PlayMode
2) Press the button START/ STOP (14). The replay
Playing
will start and
lower display line.
3) To stop the replay, press the button START/
STOP again.
For multiple replay of a recorded message:
1) Press the button of the storage location desired.
The display will show, for example:
M3 Rep2
(storage location M3,
PlayMode
replayed twice)
2) Use the button UP (12) or DN (11) to define the
number of message repeats:
= replayed 1 to 9 times,
tinuously.
3) Press the button REPEAT/ STOP (13). The
replay will start and
the lower display line.
4) To stop the replay, press the button REPEAT/
STOP again.
At a zone paging microphone PA-2500RC, PA-
1120RC or PA-6000, it is also possible to select a
message M1 – M6 and then to start the replay by
chapter 5.4).
will appear on the
Rep1 Rep9
to
Rep0
= repeated con-
Playing
will appear on
means of the button START/ STOP or to start multi-
ple replay by means of the button REPEAT/ STOP.

6.2.1.1 Immediate replay

If immediate replay has been selected by means
of the jumper PLAY MODE SELECTOR (
ter 5.2):
1) Press the button (15) of the storage location
desired. The display will now show, for example:
M3 Rep2
(storage location M3,
Playing
replayed twice)
The (multiple) replay will start immediately. The
number of replays will be indicated next to the
storage location.
2) To stop the replay, press the button REPEAT/
STOP (13).
3) When the replay has been stopped, the button
UP (12) or DN (11) can be used to change the
number of message repeats:
Rep1 Rep9
to = replayed 1 to 9 times,
Rep0
= repeated continuously.

6.2.2 Calling up a message by remote control

Instead of the buttons of the insertion module
(cf. chapter 6.2.1), the switching contacts on the
connection plate (17) can be used to replay the
messages that have been recorded on the storage
locations "M1" to "M6": Briefly connect the terminal
with the name of the corresponding button (M1, ...
M6, START [/STOP], REPEAT [/STOP]) to the ter-
minal GND (via a normally open contact). The num-
ber of repeats for multiple message replay, how-
ever, can only be changed via the buttons UP (12)
and DN (11).
Use the terminal BUSY to externally indicate
insertion module activity [analogous to the LED
indicator (26) on the circuit of the insertion module
that lights up when a message is being recorded or
replayed]. In this case, the terminal will provide
5 V against GND, and an LED, for example,
can be connected via a suitable series resistor
( fig. 4).
GB
chap-
19