Operation; Recording; Storage Locations M1 - M6; Storage Locations Voice01 - Voice20 - Monacor PA-1120DMT Bedienungsanleitung

6 Operation

GB
When the amplifier or the basic unit is switched on,
the display (4) of the insertion module will show the
weekday and the time. The unit will always auto-
matically return to this indication when, for exam-
ple, no button is pressed for approx. 30 seconds in
a menu. To cancel a menu setting at any time,
press the button MENU (10).

6.1 Recording

To record a message, connect a microphone or a
mono audio source with line level to the 2-pole jack
(7) and set the switch (9) for the input sensitivity to
the corresponding position: MIC (microphone) or
LINE (line level).
During recording, the input signal will be
replayed via the amplifier. However, it is also possi-
ble to use headphones for monitoring the input sig-
nal: Connect the headphones (minimum imped-
ance: 64 Ω) to the jack PHONES (3) [mono, only
the left side for stereo headphones); the output (25)
to the amplifier will be muted.
Please refer to chapter 6.6 for information on
how to use externally created recordings.
6.1.1 Storage locations M1 – M6
To record a message on one of the storage loca-
tions "M1" to "M6":
1) Press the button (15) of the storage location
desired. The display will show, for example:
M3
PlayMode
If pressing this button starts the replay of the
stored message, press the button REPEAT/
STOP (13) to stop the replay.
2) Press the button PLAY/REC (1). The display will
switch to the recording mode:
M3
Rec Mode
3) Press the button START/ STOP (14). First,
Erase
will appear on the lower line of the dis-
play and the storage location will be cleared.
Recording will start when the first line of the
display shows
ber. On the lower line, a bar graph will appear,
indicating the level of the input signal.
4) Use the control REC LEVEL (2) to adjust the
level of the signal to be recorded in such a way
that not all segments of the bar graph will be
shown for peaks.
5) To stop the recording, press the button START/
STOP.
18
REC
, following the storage num-
6.1.2 Storage locations Voice01 – Voice20
To record a message on one of the storage loca-
tions "Voice01" to "Voice20":
1) Press the button MENU (10). The display will
show:
Mode Set
Time
2) Press the button UP (12) or DN (11) repeatedly
Voice
until appears on the lower line of the
display.
3) Press the button ENTER (6). The display will
now show:
Choose
Play
4) Use the button UP or DN to select the option
Rec
on the lower line.
5) Press the button ENTER. The display will now
show:
Record
Voice:01
6) Use the button UP or DN to select the storage
location desired for the recording (
7) Press the button START/ STOP (14) or ENTER.
Erase
First, will appear on the lower line of the
display and the storage location will be cleared.
Recording will start when
pears. A bar graph will appear instead, indicat-
ing the level of the input signal.
8) Use the control REC LEVEL (2) to adjust the
level of the signal to be recorded in such a way
that not all segments of the bar graph will be
shown for peaks.
9) To stop the recording, press the button START/
STOP or ENTER.
PlayBack
Now, will appear on the display; the
button START/ STOP can be pressed to immedi-
ately replay the message stored. To select a differ-
ent storage location for replay, use the button UP or
DN ( chapter 6.2.3).
To exit the menu, press the button MENU.
01 20
to ).
Erase
disap-