Werbung
Verfügbare Sprachen
Verfügbare Sprachen
BassKick 100
• A headset is plugged in so that the speaker is switched off.
Plug off the headset to play via the internal speaker.
When using the LINE OUT socket, there is a humming noise.
• An electrical / magnetic alternating field intersperses onto the
conduit. Use a better cable and try to minimise the interspersion by
another passing of the conduit. If this does not help, the utilisation
of a DI box is recommended.
• Due to the earthing of the connected devices, a hum pick-up
emerges. Do in no case interrupt the ground wire of the devices but
do, if possible, operate both devices at one joint power distribution!
If this is not possible, the connection must be separated galvanically
by means of a DI box.
When connecting a mixer at the LINE OUT, the signal on the PA is
completely distorted.
• The input of the mixer is not switched to line level. Switch the
input of the mixer to line level. If this is not possible, assign an
unsymmetrical (line) input at the mixer.
The amp is too quiet.
• A device that is operated in the loop causes level losses. The effects
pedal must be levelled by means of its input/output controller.
The amp sounds too dull
• The tweeter is switched off
7
Maintenance and care
The BassKick™ amps are maintenance-free. There are, however, some
basic rules, the compliance with which secures the high useful life of
your amp:
• Do always provide for a technically unobjectionable device periphery!
• Do always provide for free air circulation at the cooling surface of
your amp.
• Do in any case avoid heavy mechanical shocks, extreme heat and
the permeation of dust and moisture.
• Do meticulously observe the specifications of additional devices.
Do never connect outputs with too large levels (e.g. power
amplifiers) to the inputs of the amp.
• Do always check the existing mains voltage before connecting
the amp to the mains supply. In case of doubt, contact the stage
technician, caretaker or similar persons.
• Please do never try to repair your amp yourself! Even the exchange
of internal fuses should be carried out by an experienced technician
only.
• The housing surface or the metal surfaces are at best cleaned with a
soft dry cloth. Do in no case use alcohol or other solvents!
8
Technical Data
Security Specifications
Mains input voltages: 240V, 220-230V, 120V, 100V
Primary fuses:
240V
220-230V
120V
100V
Secondary fuses:
Power consumption:
Ambient air temperature in operation:
Inputs
INST. INPUT:
Socket:
Input impedance:
Sensibility:
max. input level:
FX LOOP-Return:
Socket:
Input impedance:
max. sensibility:
max. input level:
Outputs
FX LOOP-Send:
Socket:
Output impedance:
Output level:
LINE OUT:
Socket:
Output impedance:
Output level:
Headphones:
Socket:
Impedance:
Speaker equipment:
1 x 15" Eminence Bass, 4 Ohm
1 x Leson ceramics tweeter, 4 Ohm
Cutoff frequency:
5 kHz
Dimensions (w,h,d) and weight:
Dimensions:
498 x 565 x 355 mm
Weight:
25.5 kg
55 lbs
T1A
T1A
T2A
T2A
2 x T2,5A
255 watts
0-35 degrees Celsius
Jack, unsymmetrical
1 MOhm
- 23,5 dBV
+ 9,3 dBV
Jack, unsymmetrical
48 kOhm
- 6 dBV
+13,5 dBV
Jack, unsymmetrical
220 Ohm
- 6 dBV
Jack, unsymmetrical
220 Ohm
0 dBV
Stereo jack
8-200 Ohm
7
Werbung
