Hitachi C 10FCH2 Bedienungsanleitung Seite 20

NOTE
Accum ulation of dust and the like inside the m otor
can result in a m alfunction.
After using the m otor for 50 hours or so, carry out no-
load running, and blow in the dry air from a w ind hole
at t h e m o t o r ' s r ear. Su ch act i o n i s ef f ect i v e t o
discharge dust and the like.
5. Inspecting the screw s
Regularly inspect each com ponent of the pow er tool
for looseness.
Re-tighten screw s on any loose part.
WARNING
To prevent personal injury, never operate the pow er
tool if any com ponents are loose.
6. Inspecting the low er guard for proper operation
Before each use of the tool, test the low er guard (see
Fig. 7) to assure that it is in good condition and that it
m oves sm oothly.
Never use the tool unless the low er guard operates
properly and it is in good m echanical condition.
7. Storage
After operation of the tool has been com pleted, check
that the follow ing has been perform ed:
(1) Trigger sw itch is in OFF position,
(2) Pow er plug has been rem oved from the receptacle,
(3) When the tool is not in use, keep it stored in a dry
place out of the reach of children.
8. Lubrication
Lubricate the follow ing sliding surfaces once a m onth
to keep the pow er tool in good operating condition
for a long tim e (Fig. 1 and Fig. 2).
Use of m achine oil is recom m ended.
Oil supply points:
* Rotary portion of hinge
* Rotary portion of vise assem bly
9. Cleaning
Periodically rem ove chips, dust and other w aste
m aterial from the surface of the pow er tool, especially
from the inside of the low er guard w ith a dam p, soapy
cloth. To avoid a m alfunction of the m otor, protect it
from contact w ith oil or w ater.
(Only M odel C10FCH2)
If the laser line becom es invisible due to chips and
the like adhered onto the w indow of the laser m arker's
light-emitting section, wipe and clean the window with
a dry cloth or a soft cloth m oistened w ith soapy w ater,
etc.
10. Service parts list
A : Item No.
B : Code No.
C : No. Used
D : Rem arks
CAUTION
Repair, m odification and inspection of Hitachi Pow er
Tools m ust be carried out by a Hitachi Authorized
Service Center.
Especially laser device should be m aintained by the
authorized agent by laser m anufacturer.
Alw ays assign the repair of laser device to Hitachi
Authorized Service Center.
This Parts List w ill be helpful if presented w ith the
tool to the Hitachi Authorized Service Center w hen
requesting repair or other m aintenance.
In the operation and m aintenance of pow er tools, the
safety regulations and standards prescribed in each
country m ust be observed.
M ODIFICATIONS
Hitachi Pow er Tools are constantly being im proved
and m odified to incorporate the latest technological
advancem ents.
Accordingly, som e parts (i.e. code num bers and/or
design) m ay be changed w ithout prior notice.
NOTE
Due to HITACHI's continuing program of research and
developm ent the specifications herein are subject to
change w ithout prior notice.
Information concerning airborne noise and vibration
The m easured values w ere determ ined according to
EN61029.
The typical A-w eighted sound pressure level: 95 dB (A)
The typical A-w eighted sound pow er level: 108 dB (A)
Wear ear protection.
The typical w eighted root m ean square acceleration
value: 2.6 m /s 2 .
Information for pow er supply system to be used w ith
electric tools provided w ith rated voltage 230 V~
Sw itching operations of electric apparatus cause voltage
fluctuations.
The operation of this electric tool under unfavorable mains
conditions can have adverse effects to the operation of other
electric apparatus.
With a m ains im pedance equal or less than 0.29 Ohm s
there w ill probably be no negative effects.
Usually, the m axim um perm issible m ains im pedance w ill
not be exceeded w hen the branch to the pow er outlet is
fed from a junction box w ith a service capacity of 25
am pere or higher.
In case of pow er failure, or w hen the pow er plug is pulled
out, im m ediately return the sw itch to OFF position. This
prevents an uncontrolled restart.
English
18