Date/Time Setting; Network Parameters Setting; Control System Data Setting (Webgate); Sasha Parameters Setting - Jacuzzi sasha Installations- Und Gebrauchsanleitung

It is necessary to use this address to initially access the configu-
ration page; where not available, you may have to temporarily
switch off the device associated to such an address, access the
control system configuration display and change the connection
data.
It may be easier to change the device data rather than that of the
control system. In any case, please consult the network adminis-
trator.
■ Select the desidered language.
■ You will be asked for a "username" and a "password": insert admin
in both fields (these parameters may be changed at a later date).
■ The display where the relative configuration parameters are to
be inserted will appear:

Date/time setting

■ Insert the date and time; click on the Set key.
Network parameter setting
■ The pre-set values are:
IP addr.: 192.168.0.100
Netmask: 255.255.255.0
Def.GW: 192.168.0.254
It is possible to change these parameters: once the new val-
ues have been inserted, click on the Set key; to activate them
switch off the control system and then turn it back on.

Control system data setting (webgate)

■ Insert, in the following order, the IP name and address rela-
tive to the installed control system.
NOTE: in the instance where multiple control systems are con-
nected to the same network, the above data must be entered for
each of the control systems. The name assigned will be present-
ed in the bottom part of the display, once it is switched on.

CHECKS

We recommend checking operation of the appliances before clos-
ing the cover of the zone in which the control system is installed, to
facilitate assessment of any malfunctions indicated by the LED.
■ Check operation of the remote control system, by also con-
sulting the LED present under the cover:
- LED PWR and STAT light up when the
control system is powered. The STAT
LED will go out after a few seconds.
In the instance where this LED begins
to flash, an error has been found: re-
fer to the Chapter "Troubleshooting".

Sasha parameters setting

■ Insert the name of the installation and system in which
Sasha is installed (see "Using the control system - preliminary
operations").
■ Insert the number of saunas and hammams connected to
the control system.
■ Assign a name to every sauna and/or hammam connected
to the control system (according to the indicated order - sauna
1, sauna 2, etc. - which corresponds to those selected during
numbering of modules, see the corresponding chapter).
■ In the instance where a SIM card is present, insert the mo-
bile telephone number(s) to receive messages notifying of
Sasha malfunctions; where a zero (0) is inserted in the space
dedicated to a telephone number, no message will be sent.
■ Tick the messages which you wish to send by clicking on
the relevant box.
NOTE: in the instance where one sole person will receive the mes-
sages, we recommend inserting their mobile telephone number
in the "user mobile" field: in this way, it is possible to activate re-
ception of warnings which would otherwise, appear in the sec-
tion reserved for "supervisor mobile".

GSM/GPRS network access parameters setting

■ Insert the GSM network access parameters for which the
SIM card is configured (consult your mobile telephone opera-
tor) and click on the Set key.

Username/password settings

■ Where necessary, it is possible to change the set username
and/or password; click on the Set key.
- When the control system is connected to the telephone line,
the GSM LED blinks intermittently (on-off 3 seconds, on-off 3 sec-
onds, etc.).
If this LED flashes continually (on-off, on-off, etc.) it is not
possible to establish a connection: refer to the Chapter
"Troubleshooting".
- the COM1 LED indicates information exchange between the
control system and Sasha; if it remains on permanently, an
error may have been identified: refer to the Chapter "Trou-
bleshooting".
- the COM2 LED is not used.
28