Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Before refilling with water wait
another 5 minutes until the appli-
ance has cooled down.
If by chance the boil-dry cut-out fails
to work an additional thermal fuse
will cut off power to the unit.
Descaling
A lime scale at the bottom of the kett-
le will cause loss of energy and can
reduce the life time of the appliance.
If the lime scale is too thick the
appliance switches off before the
water is boiling. In this case it is very
difficult to remove the lime scale.
The pot should regularly be descaled
with usual descaling agents suitable
for stainless steel.
Please consider the user instructions
of the manufacturer.
Never allow the substance to boil,
otherwise it will foam over the top of
the kettle. After descaling rinse the
kettle carefully with water.
The guarantee does not cover
damages resulting from non-keeping
of the manufacturer's instructions.
Cleaning and maintenance
Before cleaning unplug the
appliance. Never immerse the kettle
or the base into water.
Clean the inside of the kettle
occasionally. Clean the outside with
a damp cloth only. Do not use
caustic or scouring cleaning agents.
The sieve can be taken off for cleaning.
The pot is made from rust-resistant
stainless steel. Any iron moulds are only
residues which stick on the surface.
They should be removed with a special
cleansing agent for stainless steel.
Causes for failures
• Appliance switches off before
the water is boiling: The built up
lime scale at the bottom of the
kettle is too thick or the electric
circuit of the socket is overloaded.
• The appliance does not switch
off: Close the lid until it snaps in.
• Pouring the water out of the
kettle is difficult:
Descale the sieve.
• Appliance cannot be switched
on: After having used the
appliance without or too little water
the appliance has not yet cooled
down sufficiently with the thermo-
stat still in place.
If the failure cannot be removed let
the appliance have repaired.
For UK use only
• This product is supplied with a
13 A plug conforming to BS 1363
fitted to the mains lead. If the plug
is unsuitable for your socket
outlets or needs to be replaced,
please note the following. If the
plug is a non-rewireable one, cu
immediately dispose of it.
Never insert it into a socket outlet
as there is a very great risk of an
electric shock.
• The replacement of the plug at the
mains lead has to be done
according to the following
instructions:
Warning - This appliance must
be earthed
Important: The wires in this mains
lead are coloured in accordance
with the following code:
green / yellow:
Earth
blue:
Neutral
brown: Live
As the colours of the wires in the
mains lead of this appliance may
not correspond with the coloured
markings identifying the terminals
in your plug, proceed as follows:
- the wire which is coloured green
and yellow must be connected to
the terminal which is marked
with the letter E or by the earth
symbol
, or coloured green or
green and yellow,
- the wire which is coloured blue
must be connected to the
terminal which is marked with the
letter N or coloured black,
- the wire which is coloured brown
must be connected to the
terminal which is marked with the
letter L or coloured red.
• If a 13 A (BS 1363) plug is used it
must be fitted with a 13 A fuse
conforming to BS 1362 and be
ASTA approved.
If any other type of plug is used,
the appliance must be protected
by a 15 A fuse either in the plug or
adapter or at the distribution
board.
If in doubt - consult a qualified
electrician.
• Never use the plug without closing
the fuse cover.
CE
The appliance complies with the
EU regulations no. 73/ 23 EWG
and no. 89 / 336 EWG.
Subject to technical changes.
Packaging material must be
disposed in accordance with the
regulation.
5
Werbung
