Charging Mobile Devices - VOLTCRAFT PB-60 Bedienungsanleitung

Charging the battery
Fully charge the built-in rechargeable battery before first use.
Before charging the internal battery, ensure that the USB power source can deliver
a sufficient charging current, otherwise you may damage the product.
Do not use a USB port on a computer, keyboard or USB hub without power adapter
to charge the internal battery, as the current supplied by these ports is not sufficient.
Ensure that the connected devices' specifications conform to the product's
specifications listed in the technical data section.
Do not short-circuit the USB outputs.
• Fold the bracket (1) located next to the on/off switch (3) upwards.
• Connect the Micro-USB plug of the enclosed cable with the Micro-USB input (6).
• Connect the USB plug with a suitable USB power source (e.g. USB power supply with
2000 mA output current).
• The battery level indicator (2) flashes during charging.
0 – 25% 25 – 50 %
LED 1 Flashes blue Solid blue
LED 2 off Flashes blue
LED 3 off
LED 4 off
• As soon as the internal battery is fully charged, the battery level indicator lights up for about
15 seconds and then switches off automatically.
• Disconnect the cable from the product and the power source as soon as the rechargeable
battery is fully charged. The product is now ready for use.
If you only use the product occasionally, we recommend that you fully charge the
internal battery every 6 months in order to retain maximum capacity.

Charging mobile devices

• Fold the bracket (1) located next to the on/off switch (3) upwards.
• Connect your mobile device with one of the USB outputs.
The USB output Output1 (7) supplies a charging current of max. 2100 mA.
The USB output Output2 (5) supplies a charging current of max. 1000 mA.
If you connect devices to both USB outputs, the total current consumption may not
exceed 2100 mA.
The internal rechargeable battery must be fully charged to charge 2 devices
simultaneously.
• If the charging process does not start automatically, press the on/off switch (3).
• Monitor the charging process. Remove the USB cable from the product and the mobile
device as soon as the charging process is complete.
If the charging status is less than 2 %, the product automatically turns off to prevent
excessive discharge of the internal battery.
LED light
• Press the on/off switch (3) to turn the LED light (4) on.
• Press the on/off switch again to change the light mode:
Full luminosity → reduced luminosity → strobe → off
• Press and hold the on/off switch for approx. 2 seconds to send an SOS signal with the light.
• To turn off the SOS signal, briefly press the on/off switch.
Carabiner/suspension bracket
• Connect the carabiner with one or both suspension brackets (1) to hang the product.
• You can also hang the product on a suitable hook without the carabiner. Make sure that the
product does not fall.
50 – 75 % 75 – 99 %
Solid blue Solid blue
Solid blue Solid blue
off Flashes blue Solid blue
off off Flashes blue
Care and cleaning
• Disconnect the product from the connected devices before cleaning.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the casing or cause the product to malfunction.
• Do not immerse the product in water.
• This product does not contain any components that require maintenance. Never attempt to
open or disassemble it.
• Use a lint-free cloth to clean the product. Do not press too hard on the housing, as this can
lead to scratch marks.
• Dust can be easily removed using a soft and clean long-haired brush.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. Always dispose of the product according to the relevant statutory
regulations.
You thus fulfil your statutory obligations and contribute to the protection of the
100 %
environment.
Solid blue
Technical data
Solid blue
Input voltage/current ..................... 5 V/DC, 2 A
Solid blue
Output voltage/current .................. 5 V/DC, 2.1 A (total)
Solid blue
Rechargeable battery ................... LiPo, 3.7 V, 6000 mAh
Number of LEDs ........................... 18
Charging duration ......................... approx. 3.75 h via USB
Colour temperature ....................... 6000 – 6500 k
Protection type .............................. IP54
Cable length ................................. approx. 30 cm
Operating/storage temperature .... 0 to +45 °C
Dimensions (L x W x H) ................ 150 x 77 x 15 mm
Weight .......................................... 193 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE. *1661733_v1_0518_02_IPL_m_en