Introduction - Parkside PKS 1500 A1 Betriebsanleitung

Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D-89335 Ichenhausen
NOTE:
According to the applicable product liability laws, the ma-
nufacturer of the device does not assume liability for da-
mages to the product or damages caused by the product
that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due
to the non-compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113.
WE RECOMMEND:
Read through the complete text in the operating instruc-
tions before installing and commissioning the device.
The operating instructions are intended to help the user
to become familiar with the machine and take advan-
tage of its application possibilities in accordance with the
recommendations. The operating instructions contain
important information on how to operate the machine
safely, professionally and economically, how to avoid
danger, costly repairs, reduce downtimes and how to in-
crease reliability and service life of the machine.
In addition to the safety regulations in the operating in-
structions, you have to meet the applicable regulations
that apply for the operation of the machine in your count-
ry. Keep the operating instructions package with the ma-
chine at all times and store it in a plastic cover to protect
it from dirt and moisture. Read the instruction manual
each time before operating the machine and carefully
follow its information. The machine can only be operated
by persons who were instructed concerning the operati-
on of the machine and who are informed about the asso-
ciated dangers. The minimum age requirement must be
complied with.
Legend of Fig. 1
1 Start button
2 Handle
3
Locking lever
4 Motor
5 Saw blade
6 Moving saw blade guard
7 Base
8 Table insert
9 Rotary table
10 Workpiece clamp
11 Housing / base joint
12 Dust bag
13 Stationary saw blade guard
2 GB/IE/CY
PKS 1500 A1
Scope of delivery
Workpiece clamp
Tool for saw blade replacement
2 work piece supports
2 batteries (AAA)
2 carbon brushes
Operating instructions
Technical Data
Dimensions L x W
690 x 550 x 440
x H mm
Rotary table ø mm
Table height mm
Saw blade Ø mm
Number of teeth
Speed rpm
Cutting speed m/s
Pivot range
Tilt angle
Double mitre
45° x 45°
45°, 30°, 22,5°, 15°, 0°,
Catch positions
15°, 22,5°, 30°, 45°
Weight kg
Cross-cutting data
Max. cut depth
90°/45°
90°/90°
90°/45°
45°/90°
45°/45°
Drive
Motor V/Hz
S6 25% 1500W
Rated input W
Technical changes reserved!
*S6, continuous operation periodic duty.
Identical duty cycles with a period at load followed by a period at
no load. Running time 10 minutes; duty cycle is 25% of the running
time.
The work piece must have a minimum height of 3mm
and a minimum width of 10 mm.
Make sure that the workpiece is always secured with
the clamping device.
Information about noise development
The noise levels of this machine during operation are as
follows:
L : 99.6dB(A) K=3dB(A)
pA
L : 112.6dB(A) K=3dB(A)
wA
Vibration: 4.51m/s K=1.5m/s
2 2
Warning: Noise can have serious effects on your health.
If the machine noise exceeds 85 dB (A), please wear
suitable hearing protection. If the electrical connection
is defective, the power can fail when starting the machi-
ne. This could influence other machines (e.g. blinking
lamps). If the electrical power corresponds to Zmax <
0.27, such disruptions should not occur. (However, if
they do, inform your specialist dealer).
Mitre saw
Dust bag
spanner size 6
Support stand
385 x 150
55
210/30/2,6
48
5000
55
2 x 45°
45°
left
7,7
60 / 35 mm
120 x 60 mm
80 x 60 mm
120 x 35 mm
80 x 35 mm
220-240~ / 50