Specifications - Pioneer ND-BC8 Bedienungsanleitung

1 Pull out from here
2 Hinge
3 Harness cover
4 Rear view
camera
5 Hatch
Fig. 11
Abb. 11
2 Waterproof pad
1 Clamps
4 Make a U-shaped loop in
the lead outside the rubber
packing to prevent rainwa-
ter from flowing along the
3 Rubber packing
lead into the interior of the
vehicle.
Attach the waterproof pad
using double-sided tape.
Fig. 12
Abb. 12
Connection <ENGLISH>
Notes: Accessory power supply
• This unit is for vehicles with a 12-volt battery and nega-
To electric terminal controlled by ignition
tive grounding. Before installing it in a recreational vehi-
cle, truck, or bus, check the battery voltage. switch (12 V DC) ON/OFF.
• To avoid shorts in the electrical system, be sure to discon-
3 Red
nect the battery cable before beginning installation.
4 Fuse (1 A)
• Refer to the owner's manual for details on connecting the
other units, then make connections correctly. Ground
• Secure the wiring with cable clamps or adhesive tape. To
protect the wiring, wrap adhesive tape around them where To vehicle (metal) body.
they lie against metal parts.
5 Black
• Route and secure all wiring so it cannot touch any mov-
ing parts, such as the gear shift, parking brake and seat Cord installation (Fig. 10)
rails. Do not route wiring in places that get hot, such
as near the heater outlet. If the insulation of the wiring
1 Clamps
melts or gets torn, there is a danger of the wiring short-
circuiting to the vehicle body. 2 Rear view camera
• Do not shorten any leads.
3 RCA power supply cable
• Never feed power to other equipment by cutting the insu-
4 Product with a video input jack
lation of the power supply lead of the unit and tapping
(Hideaway unit etc.)
into the lead. The current capacity of the lead will be
exceeded, causing over heating. 5 Made with a rasp etc.
• When replacing the fuse, be sure to only use a fuse of the 6 Scuff plate
rating prescribed on the fuse holder.
7 Clamp
• To minimize noise locate the TV antenna cable, radio
8 Waterproof pad
antenna cable and RCA power supply cable as far away
Attach the waterproof pad using double-
from each other as possible.
sided tape.
• Connection to a TV with an RCA video input is possible,
but confirm whether the TV you use has a reverse gear
Cord installation points (Fig. 11, Fig. 12)
connection function.
• If this unit is installed in a vehicle that does not have an
ACC (accessory) position on the ignition switch, the red • When pulling the cord out of the car,
lead of the unit should be connected to a terminal coupled
pull from the outer side of the hatch har-
with ignition switch ON/OFF operations. If this is not
ness cover and hinge. (Fig. 11)
done, the vehicle battery may be drained when you are
away from the vehicle for several hours.
1 Pull out from here
2 Hinge
3 Harness cover
4 Rear view camera
5 Hatch
• When the rear view camera cord cannot
be pulled out from the lower side, bend
the cord into a U shape in front of the
ACC position No ACC position
waterproof pad, making sure that rainwater
cannot enter the car by running down the
• Cords for this product and those for other products may cord. (Fig. 12)
be different colors even if they have the same function.
1 Clamps
When connecting this product to another product, refer to
2 Waterproof pad
the supplied manuals of both products and connect cords
3 Rubber packing
that have the same function.
4 Make a U-shaped loop in the lead outside
the rubber packing to prevent rainwater from
Connection sample (Fig. 9)
flowing along the lead into the interior of the
vehicle.
1 Rear view camera Attach the waterproof pad using double-
Video input jack sided tape.
After cord installation
Connect to camera input jack (REAR
VIEW CAMERA IN).
Open and close the hatch door slowly to confirm
2 RCA pin
that the cord is not rubbing against the rim of
the door.

Specifications

<ENGLISH>
Power source ........................................... 14.4 V DC Dimensions (W × H × D)
(10.8 V to 15.1 V allowable) ..................... 23.8 mm × 23.8 mm × 25.5 mm
Grounding system .............................. Negative type (7/8 in. × 7/8 in. × 1 in.)
Max. current consumption ............... 100 mA or less Weight ................................................. 186 g (0.4 lbs)
Output video ....................................... Mirror image (including the cable)
(for rear view confirmation) Length
Sensor ......................... 1/4-inch color CMOS sensor Rear view camera cable .......... 3 m (9 ft. 10 in.)
No. of pixels RCA power supply cable ...... 7 m (22 ft. 12 in.)
.................. effective no. of pixels roughly 310 000
Note:
Lens ........................................................ Wide-angle,
Specifications and the design are subject to possible
focal length f = 1.12 mm, F value 2.3
modification without prior notice due to improve-
Angle of view .................. Horizontal: approx. 129 º
ments.
Vertical: approx. 105 º
IR cutoff filter (special filter for vehicle mounting)
.................................................................. Provided
Iris system .......................................... Electronic iris
Scanning system ........................................ Interlace
Synchronizing system ....... Internal synchronization
Signal-to-noise ratio .......................... 40 dB or more
(at the recommended intensity of illumination)
Horizontal resolution ............ Approx. 350 TV lines
Illumination range .... Approx. 0.9 lux to 100 000 lux
Image output ........ NTSC compatible 1 Vp-p (75 Ω)
Operation temperature range ......... –30 ºC to +70 ºC
–22 ºF to +158 ºF
Storage temperature range ............ –40 ºC to +85 ºC
–40 ºF to +185 ºF