Mounting The Bar And Chain; Before Start - Fuel And Chain Oil; Start / Stop; To Start A Cold Engine - Texas Pro Chainsaw 300 Betriebsanleitung

Adjustment of chain oil amount:
MAX = Increase, MIN = Reduce
Carburetor adjustment - Low speed
L
(for service place only)
Carburetor adjustment - high speed
H
(for serviceplace only)
T
Carburetor adjustment - Idle speed

Mounting the bar and chain

See Fig. 2 and illustration:
1. Pull the chain brake lever back toward the machine
so that the brake is not activated
2. Loosen the nuts and remove the plastic cover (3)
3. Place the bar on the threaded (1) and push it
toward the drive wheel.
4. Place the chain on the drive wheel with teeth
pointing forward (towards the tip). See Fig. F3
Place the chain drive links, so there is correctly
engaged with the gear teeth
5. Ensure that the chain fits precisely on the bar
6. Install the plastic screen (3). Make sure that the
chain sitting correctly in the hole.
7. Before the nuts are tightened, tighten the chain
using. Chain tensioner (1) until it fits perfectly.
See Fig. 4
(2) = loosened chain
(3) = chain is tightened
The chain should be so tight that you can just lift
drivleddel free of the trace of the bar.
The saw chain has very sharp teeth.
Always use protective gloves when
mounting / dismounting / adjusting the
chain.
Note: A new chain can expand in length in the
beginning. You should therefore periodically to inspect
and tighten it - as a loose chain can jump off and cause
wear of the chain and the bar.
Before start – fuel and chain oil
• This product is equipped with a 2-stroke engines
that require two-stroke oil added to the gasoline.
• Always use unleaded gasoline (minimum octane 95)
• Do not use ready-mixed gasoline / oil from gas
stations, which are intended for use in mopeds,
motorcycles etc.
• Always use oil supplier's regulations regarding the
mix of (see the back of the bottle).
• Use a clean and approved petrol can for mixing
petrol with oil.
• Use an approved 2-stroke oil for air cooled engines,
chainsaws, trimmers and the like.
•
(Do not use outboard motor oil or lubrication oil for
cars). Mix in small quantities.
• Texas recommends Alco Multi-Mix universal two-
stroke oil - Art. no. 90406520 (0.1 L) / 90406521
(1 L) were mixed at a ratio of 2.5% (40: 1). This is
equivalent to
0.1 liters of 2-stroke
oil is mixed with
4 liters of gasoline.
If another oil is used a 4%. Follow always
manufacturer's instructions and petrol.
• Mix oil and gasoline thoroughly and shake the can
before filling (Fig. 5)
• Never use a gasoline mixture that is more than
90 days old when the engine in this case may have
difficulty starting. Never store the same mixture in
the tank for more than 30 days.
For prolonged storage, empty the tank.
Refuelling - No Smoking!
1. Screw the lid slowly. Put it on a clean surface.
2. Carefully pour the oil mixed fuel in the tank, avoid
waste.
3. Screw the lid on tightly by hand.
4. Wipe up spilled fuel.
Note: Always turn off the engine before refueling, never
pour fuel on a machine that is running or when the
engine is hot. Move at least 3 meters away from fueling
site before starting the engine. Least 2-minute break
before refueling of fuel.
Fuelling (Smoking is prohibited)
Mix and store fuel in containers approved for this.
Mix only fuel outdoors where there are no sparks or
flames.
Select bare ground, stop the engine and let it cool at
least 2 minutes before refueling.
Loosen fuel cap slowly to relieve the pressure and
prevent the fuel flowing out under the cover.
Wipe any spilled fuel. Move the machine 3 meters
away from fueling site before starting the engine.
Chain oil
Always use chain oil for lubrication of bar and chain.
Texas recommends Alco chain oil SAE 30th
Nature. no. 90406590 (1 L) / 90406502 (4 L)

Start / Stop

To start a cold engine

1. Fill the chain oil (1) and fuel (2). See Fig. 6th
2. Add the power chain saw on a firm and place.
3. Ensure that the chain brake is not activated
(drag chain break handle back)
4. Turn the stop / start switch (3) up. See Fig. 7th
5. Pull out the choke (4) completely. See Fig. 8
6. While hold the saw firmly on the ground with
the foot inside the rear handle (let the foot
throttle trigger at the same time), pull the
starter handle a few times with your right hand
until the first ignition attempt is heard. See Fig.
9
7. Push the choke into
8. Pull the starter rope again until the engine
starts.
9. After 6-7 seconds, assets safety lever (6) and
press the throttle (5) and to give the engine
revs. See Fig. 10th
10. Repeat steps 5-8 for starting not succeeded.
16