Bosch PWS 700 Bedienungsanleitung Seite 17

Grinding/Cutting Disc
Observe the dimensions of the grinding discs.
The hole diameter
flange 8 (M 14), 19 (M 10). Do not use any re-
ducers or adapters.
When using a diamond cutting disc, take care
that the direction-of-rotation arrow on the dia-
mond cutting disc and the direction of rotation of
the machine (direction-of-rotation arrow on the
machine head) agree.
For mounting, see the illustration page.
Screw on the clamping nut 10 and tighten with
the two-pin spanner (see Section "Quick-clamp-
ing Nut").
8
If the O-ring is missing or is damaged, it must
in all cases be
1 600 210 039) before the mounting flange 8 is
mounted.
19
The bore of the diamond cutting disc (Ø 20 mm)
must fit the spigot of the mounting flange 19 with-
out any play.
Do not use any reducers or adapters.
After mounting the grinding tool and be-
fore switching on, check that the grind-
ing tool is correctly mounted and that it
can turn freely.
Flap Disc
(for M 14 grinder spindle)
Depending on the application, remove the protec-
tion guard 6 and mount the hand guard 12. Place
the special mounting flange 8 (accessory, Order
No. 2 605 703 028) and the flap disc on the
grinder spindle 5. Screw on the clamping nut 10
and tighten with the two-pin spanner.
18 • 1 609 929 F32 • 03.06
must fit mounting
Mounting flange for
grinding spindle
M 14
An O-ring (plastic
part) is inserted in the
mounting flange 8
around the spigot.
replaced (Order
Mounting flange for
grinding spindle
M 10
The mounting
flange 19 can
used on both sides.
For diamond cutting
discs it must be posi-
tioned on the grind-
ing spindle 5
turned through 180°.
Rubber Sanding Pad 13
Depending on the application, remove the protec-
tion guard 6 and mount the hand guard 12.
For mounting, see the illustration page.
Screw on the round nut 15 and tighten with the
two-pin spanner.
Cup Brush 16/Disc Brush
(for M 14 grinder spindle)
Depending on the application, remove the protec-
tion guard 6 and mount the hand guard 12.
The grinding tool must be able to be screwed
onto the grinding spindle 5 until it rests firmly
against the grinder spindle flange at the end of
the grinder spindle threads. Tighten with an
open-end spanner.
Quick Clamping Nut
(for M 14 grinder spindle)
Instead of the clamping nut 10, the quick-clamp-
ing nut 11 (accessory) can be used. Grinding
tools can then be mounted without using tools.
The quick-clamping nut 11 may be used only
No.
for grinding and cutting discs.
Use only a flawless, undamaged quick-clamp-
ing nut 11.
When screwing on, take care that the side with
printing does not point to the grinding disc. The
arrow must point to the index mark 20.
be
11
and
4
4
English - 5
Lock
20
spindle with the spin-
dle lock
Tighten the quick-
clamping
forcefully turning the
grinding disc in the
clockwise direction.
A properly tightened
undamaged,
clamping nut can be
loosened by hand
turning the knurled
ring in the counter-
clockwise direction.
Never loosen a tight
quick-clamping nut
with pliers but use a
two-pin spanner. In-
sert the
spanner as shown in
the illustration.
the grinder
button 4.
nut by
quick-
two-hole