Declaration Of Conformity; Mounting And Operation - Bosch AQT 42-13 Originalbetriebsanleitung

16 | English

Declaration of Conformity

We declare under our sole responsibility that the product described under "Technical data"
is in conformity with the following standards or standardization documents: EN 60335 ac-
cording to the provisions of the directives 2011/65/EU, 2004/108/EC, 2006/42/EC,
2000/14/EC.
2000/14/EC: Guaranteed sound power level:
Conformity assessment procedure according to Annex V.
Equipment category: 27
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-LG/ENS23,
Stowmarket, Suffolk IP14 1EY, England
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
13.03.2014

Mounting and Operation

Action
Delivery Scope
Adjusting the Handle
Connecting high pressure gun to lance
Connecting high pressure water supply hose/
nozzle
Attaching Nozzle
Water connection
Switching On and Off
Clean the water filter
Clean nozzle
Gun storage
Gun/lance/nozzle is stored in action
Hose into the hose holder
Storage
Selecting Accessories
Starting
For Your Safety
Warning! Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
The operating voltage is 230 V AC, 50 Hz (for non-EU coun-
tries 220 V, 240 V as applicable). Only use approved exten-
sion cables. Contact your Bosch Service Centre for details.
F 016 L81 056 | (11.4.14)
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Figure
1
2
3
4
5
6
7
8
9
10
11
12
13
14
If you want to use an extension cable when operating your
high pressure washer, only the following cable dimensions
should be used:
2
– 1.5 mm – max length 20 m
2
– 2.5 mm – max length 50 m
Note: If an extension cable is used it must be earthed and con-
nected through the plug to the earth cable of your supply net-
work in accordance with prescribed safety regulations.
If in doubt contact a qualified electrician or the nearest Bosch
Service Centre.
WARNING! Inadequate extension cables can
be dangerous. Extension cable, plug and sock-
et must be of watertight construction and in-
tended for outdoor use.
Cable connections should be kept dry and off the ground.
For increased electrical safety to use a Residual Current De-
vice (RCD) with a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.
If the supply cord is damaged, it must be replaced by a Bosch
Service Centre.
For products not sold in GB:
WARNING: For your safety, it is required that the plug at-
tached to the machine is connected with the extension cord.
The coupling of the extension cord must be protected against
splash water, be made of rubber or coated with rubber. The
extension cord must be used with a cable strain relief.
To prevent damage to the appliance, do not allow it to operate
dry.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
3 600 ... HA7 3.. HA7 4..
dB(A) 95
Bosch Power Tools
95