Technical Data; Noise/Vibration Information; Declaration Of Conformity; Mounting And Operation - Bosch GHP 5-13 C Originalbetriebsanleitung

OBJ_DOKU-31942-002.fm Page 11 Wednesday, September 5, 2012 1:03 PM

Technical Data

Pressure washer
Article number
Rated power
Supply Temperature max.
Supply rate min.
Rated pressure
Max. operating pressure
Flow rate
Maximum input pressure
Repulsive force at the gun to the
maximum pressure
Motor Insulation
Motor Protection
Detergent tank
Autostop function
Net impedance
Weight according to
EPTA-Procedure 01/2003
Protection class
Serial number
Starting cycles generate brief voltage drops. Interference with other
equipment/machines may occur in case of unfavourable mains system
conditions. Malfunctions are not to be expected for system impedances
below 0.153 ohm.

Noise/Vibration Information

Measured sound values determined according to
2000/14/EC (1.60 m height, 1 m distance away).
Typically the A-weighted noise levels of the product are:
Sound pressure level 81.8 dB(A); sound power level
90 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60335:
2 2
a =3.12 m/s , K=1.5 m/s .
h

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with the fol-
lowing standards or standardization documents: EN 60335
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC, 2000/14/EC.
2000/14/EC: Guaranteed sound power level 90 dB(A). Con-
formity assessment procedure according to Annex V.
Equipment category: 27
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-LG/ENS,
Stowmarket, Suffolk IP14 1EY, England
Bosch Power Tools
Dr. Egbert Schneider
Senior Vice President
Engineering
GHP 5-13 C
3 600 J10 0..
kW 2.3
°C 50
Robert Bosch GmbH, Power Tools Division
l/min 8.3
D-70745 Leinfelden-Echterdingen
29.06.2012
MPa 13
MPa 14

Mounting and Operation

l/min 8.3
MPa 1
Action
Delivery Scope
N 22.11
Insert dip stick for ventilation
Class F
Connect detergent bottle
IPX5
Water connection
–
Clean the water strainer
Connecting high pressure water supply hose/
nozzle
Ω
Adjust water pressure
kg 16.5
Adjust water jet
/I
Switching on and off
See serial number
Working Advice
(rating plate) on pressure
Clean nozzle
washer.
Starting
For Your Safety
Your pressure washer requires an earth connection. The op-
erating voltage is 230 V AC, 50 Hz (for non-EU countries
220 V, 240 V as applicable). Only use approved extension ca-
bles. Contact your Bosch Service Centre for details.
If you want to use an extension cable when operating your
high pressure washer, only the following cable dimensions
should be used:
– 2.5 mm
– 4.0 mm
Note: If an extension cable is used it must be earthed and con-
nected through the plug to the earth cable of your supply net-
work in accordance with prescribed safety regulations.
If in doubt contact a qualified electrician or the nearest Bosch
Service Centre.
Cable connections should be kept dry and off the ground.
For increased electrical safety to use a Residual Current De-
vice (RCD) with a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Warning! Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
2
– max length 20 m
2
– max length 50 m
WARNING! Inadequate extension cables can
be dangerous. Extension cable, plug and sock-
et must be of watertight construction and in-
tended for outdoor use.
F 016 L72 354 | (5.9.12)
English | 11
Figure
1
2
3
4
5
6
7
8
9
10
11