Siemens SIWAREXFTC Handbuch Seite 149

Projektieren in SIMATIC PCS 7
SLOT_NO BYTE
BASADR INT
DADDR INT
WORD
LADDR
BOOL
MANOP_EN
BOOL
AUTOP_EN
BOOL
LIOP_SEL
BOOL
AUT_L
MSG_LOCK BOOL
SAMPLE_T REAL
RUNUPCYC INT
EV_ID1 DWORD
EV_ID2 DWORD
BA_EN BOOL
OCCUPIED BOOL
BA_ID DWORD
BA_NA STRING[32]
STEP_NO DWORD
INT
AUT_CMD
BOOL
AUTCMDEN
REAL
SIM_VAL
REAL
ANA_OUT
BYTE
DO_FORCE
BYTE
TRANSITION
SIG1_6 BOOL
SIG1_7 BOOL
SIG1_8 BOOL
AUX2PR08 ANY
AUX2PR09 ANY
AUX2PR10 ANY
AUT_ON_OP BOOL
MAN_CMD INT
CPY_M_A BOOL
BOOL
QCSF
QPARF BOOL
QMODF BOOL
QPERAF BOOL
QRACKF BOOL
SFC_ERR_C WORD
L_DR_NO INT
L_CMD INT
BOOL
QMAN_AUT
QMANOP BOOL
QAUTOP BOOL
M_CMD_EN BOOL
BOOL
QMSG_ERR
BOOL
QMSG_SUP
QMSGERR1 BOOL
QMSGERR2 BOOL
MSG_STAT1 WORD
MSG_ACK1 WORD
MSG_STAT2 WORD
MSG_ACK2 WORD
BOOL
CMD_INPR
BOOL
CMD_FOK
SIWAREX FTC 12-137
I 0 Slot Number
I 0 Base Adress of Siwarex-FT Module
I 0 Diagnostic Address of Siwarex-FT
Module
I 0 Base Adress of Siwarex-FT Module
I TRUE Enable: 1=Operator may input MANUAL
I TRUE Enable: 1=Operator may input AUTO
I FALSE Select: 1=Linking, 0=Operator active
I TRUE Linkable Input for MANUAL/AUTO mode
I FALSE Message Lock
I 0.1 Sample Time [s]
I 10 Lag: Number of Run Up Cycles
I 0 Message ID
I 0 Message ID
I FALSE Batch Enable
I FALSE Occupied by Batch
I 0 Batch ID
I Batch Name
I 0 Batch Step Number
I 0 Auto Command
I FALSE Execute command in Automatic Mode
I 0.0 Simulation for weigh value
I 0.0 Value for analog output
I 16#00 Force digital output for service
I 16#00 Transition for automatic weighing step
I FALSE free Message EV_ID1/Message 6
I FALSE free Message EV_ID1/Message 7
I FALSE free Message EV_ID1/Message 8
IO Auxiliary Value 8/ EV_ID2
IO Auxiliary Value 9/ EV_ID2
IO Auxiliary Value 10/ EV_ID2
IO FALSE Operator Input Mode 1=AUTO,
0=MANUAL
IO 0 Manual Command
IO FALSE Copy manual values to automatik inputs
O FALSE 1=Control System Fault
O FALSE 1=Parametration failure
O FALSE 1=Module failure
O FALSE 1=Peripherie access failure
O FALSE 1=Rack failure
O 0 Errorcode of last SFC call
O 0 Last transferred Data Record
O 0 Last transferred Command
O FALSE 1=AUTO, 0=MANUAL Mode
O FALSE Status: 1=Operator enabled for
MANUAL
O FALSE Status: 1=Operator enabled for AUTO
O TRUE Enable: 1=Operator may input new
MAN_CMD
O FALSE 1=Message Error
O FALSE 1=Message Suppression Active
O FALSE 1=Message ERROR
O FALSE 1=Message ERROR
O 0 Message: STATUS Output
O 0 Message: ACK_STATE Output
O 0 Message: STATUS Output
O 0 Message: ACK_STATE Output
O FALSE Command in progress
O FALSE Command finished ok
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x