Troubleshooting And Faq - Geneva AeroSphère Large Installationsanleitung

vIII

TroUBlEShooTInG AnD FAQ

See also areosphere.genevalab.com
GEnErAl
Why are there two buttons on the remote control?
The upper refers to the LINE-IN analog audio input on the back of
an AeroSphère speaker.
The lower ( next to CD ) selects the analog audio input on the
back of the AeroSphère Base. Audio from this input is streamed to all
connected AeroSphère speakers.
how do I change the battery in the remote control?
1. Locate the small hole on the black side facing the user.
2. Gently push the included pin into this hole and push in.
Alternatively you can use a safety pin.
3. Push the pin gently to the left side.
4. The battery compartment will slide out. Replace the battery ( 3V
lithium cell, 3V CR2032 ). Verify that the battery is inserted with the
right polarity ( + side is facing down ).
3
how do I change the bass and treble?
Use the music note icon in the AeroSphère app.
Power consumption in standby
AeroSphère large: 0.47 Watt ( Powering off: use the
remote control or the power button on the back of the speaker )
AeroSphère Small: 0.3 Watt ( Powering off: use the
remote control or the power button on the back of the speaker )
AeroSphère Base: 0.3 Watt ( Powering off: slide power switch to
"OFF" position )
Why is the AeroSphère Small or AeroSphère large turning itself off?
The AeroSphère speaker will automatically turn itself off after 15
minutes if there is no active audio input. This is an Energy saving
functionality, required by law in many countries.
WI-FI SETUP
how to reset to factory default settings
AeroSphère speakers: Hold the power button on the back of the
speakers for 10 seconds, until the display starts blinking red. Then
remove your finger from the button.
AeroSphère Base: Hold the Wi-Fi button for a few seconds while
turning the power switch from OFF to ON position.
16
4
2
button on
button on
What happens when I do reset to factory defaults?
1. The Wi-Fi network settings are reset.
2. The Wi-Fi setup method WAC is started ( AeroSphère speakers only ).
Are WAc and "network setup webpage" methods active at the
same time?
Yes, both methods are available at the same time. If you have an iOS
device with iOS 7 or higher, you are not able to select the temporary
Wi-Fi network from the Wi-Fi menu in the iOS preferences. With an iOS
device with iOS 6 or lower, you will not see the WAC method in the Wi-
Fi setup menu.
BlUETooTh
I cannot connect to the AeroSphère speaker.
1. Select Bluetooth with the remote control – the display must be blue
( constant or flashing ).
2. If the display is NOT flashing, another device has already been
connected. This device must first be turned off - only one device
can be connected at the same time.
3. Reset Bluetooth with the instructions below.
how to reset Bluetooth
Up to eight paired Bluetooth devices can be stored. To clear the
memory, perform the following steps:
1. Turn on the AeroSphère speaker and select
control.
2. Within 5 seconds of entering Bluetooth mode, hold down the
button on the remote control for at least 5 seconds.
3. Pair your mobile phone again.
During pairing, my smartphone requests a PIn—what is the PIn?
If the phone asks for a PIN, enter "0000" ( four zeros ).
AIrPlAY
I don't see the AeroSphère speaker show up in the AirPlay icon
of iTunes
The AirPlay icon in iTunes or iPhone only shows if an AirPlay speaker
has been discovered in your Wi-Fi network. Make sure the AeroSphère
speaker is successfully connected to your home network. The display
must be constant green.
how do multiple AirPlay speakers in the same network
behave together?
iTunes can play to more than one AirPlay speaker at the same time. The
music will always be synchronized.
SUPPorT
Service and repair
If the product is damaged and needs repair, please contact your dealer.
Visit www.genevalab.com to find a dealer in your area.
Warranty
See the specific terms for your country at www.genevalab.com.
with the remote