Getting Started - Dremel 200 Übersetzung Der Originalbetriebsanleitung

4. With the shaft lock engaged twist nose cap clockwise
to tighten the collet nut.
5. Screw the nose cap back into its original position.
NOTE: Be sure to read the instructions supplied with
your Dremel accessory for further information on its
use.
Use only Dremel tested, high performance accessories.
BALANCING ACCESSORIES
For precision work, it is important that all accessories
be in good balance (much the same as the tires on
your automobile). To true up or balance an accessory,
slightly loosen collet nut and give the accessory or collet
a 1/4 turn. Re tighten collet nut and run the Rotary Tool.
You should be able to tell by the sound and feel if your
accessory is running in balance. Continue adjusting in this
fashion until best balance is achieved.
USING ATTACHMENTS
Your Dremel can be equipped with different attachments
that expand the functionality of your tool.
NOTE
Not all attachments listed below are included in your kit.
Use only Dremel tested, high performance attachments!
You can order attachments through the Dremel Service
Center or go to www.dremel.com for attachment and
accessory compatibility.
1. Use the Flexible Shaft (225) for precise, detailed work
or hard to reach places. SEE PAGE 7.
NOTE
For optimum performance allow your new Flexshaft to
run at high speed on your multitool in a vertical position
for 2 minutes before use.
2. Use the Dremel Shaping Platform (576) to sand and
grind at perfect 90 and 45 degree angles.
SEE PAGE 9.
3. Use the Dremel Detailer's Grip (577) to have even
better control of your Multitool. SEE PAGE 8.
4. Use the Multipurpose Cutting Kit (565/566) for
controlled cutting in a variety of materials.
SEE PAGE 10.
5. Use the Wall & Floor Grout Removal Kit (568) for
removing grout from between wall and floor tiles. SEE
PAGE 11.
6. Use the Line & Circle Cutter (678) to make perfect
holes and straight cuts. SEE PAGE 12.
7. Use the Right Angle Attachment (575) to use
accessories in right angle for hard to reach places.
SEE PAGE 13.
8. Use the Comfort Guard Attachment to protect you from
dust and sparks. SEE PAGE 14.

GETTING STARTED

The first step in using the multitool is to get the "feel" of it.
Hold it in your hand and feel its weight and balance. Feel
the taper of the housing. This taper permits the tool to be
grasped much like a pen or pencil.
Always hold the tool away from your face. Accessories
can be damaged during handling and can fly apart as they
come up to speed.
USE
When holding tool, do not cover the ventilation openings
with your hand. Blocking the ventilation openings could
cause the motor to overheat.
IMPORTANT! Practice on scrap material first to see how
the tool's high-speed action performs. Keep in mind that
your multitool will perform best by allowing the speed,
along with the correct Dremel accessory and attachment,
to do the work for you. Do not put pressure on the
tool during use, if possible. Instead, lower the spinning
accessory lightly to the work surface and allow it to touch
the point at which you want to begin. Concentrate on
guiding the tool over the work using very little pressure
from your hand. Allow the accessory to do the work.
Usually it is better to make a series of passes with the tool
rather than to do the entire job with one pass. A gentle
touch gives the best control and reduces the chance of
error.
HOLDING THE TOOL
For best control in close work, grip the multitool like a
pencil between your thumb and forefinger. PICTURE 13
The "golf" grip method is used for heavier operations such
as grinding or cutting. PICTURE 14
OPERATING SPEEDS
To select the right speed for each job, use a practice piece
of material.
SLIDE "ON/OFF" SWITCH
The tool is switched "ON" by the slide switch located on
the top side of the motor housing.
TO TURN THE TOOL "ON", slide the switch button
forward.
TO TURN THE TOOL "OFF", slide the switch button
backward.
HIGH PERFORMANCE MOTOR
Your tool is equipped with a high performance rotary tool
motor. This motor expands the versatility of the rotary tool
by driving additional Dremel attachments.
ELECTRONIC FEEDBACK
Your tool is equipped with an internal electronic feedback
system that provides a "soft start", which will reduce the
stresses that occur from a high torque start. The system
also helps to keep the preselected speed virtually constant
between no-load and load conditions.
VARIABLE SPEED DIAL
Your tool is equipped with a variable speed dial. The speed
may be adjusted during operation by presetting the dial on
or between any one of the settings.
The speed of Rotary Tool is controlled by setting this dial
on the housing. PICTURE 12
25