Noise/Vibration Information - Bosch GSC 2,8 Professional Originalbetriebsanleitung

OBJ_BUCH-598-003.book Page 10 Friday, April 29, 2016 3:35 PM
10 | English
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 On/Off switch
2 Auxiliary handle
3 Screw for auxiliary handle
4 Auxiliary-handle mount
5 Adjustment screw, upper cutter
6 Striker
7 Upper cutter
8 Fastening screw for upper cutter
9 Bottom cutter
10 Cutting base
11 Adjustment screw, bottom cutter
12 Fastening screw for bottom cutter
13 Setting gauge
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Sheet Metal Shears
Article number
Rated power input
Output power
Stroke rate at no load n
0
Stroke speed under load
Max. steel sheet cutting capacity*
Weight according to
EPTA-Procedure 01:2014
Protection class
2
* to 400 N/mm with reference to steel sheet
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-8.
Typically the A-weighted sound pressure level of the product
is 80 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a = 22 m/s , K< 2 m/s .
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
1 609 92A 2PV | (29.4.16)
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards:
EN 60745-1, EN 60745-2-8, EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Henk Becker
Executive Vice President
GSC 2,8
Engineering
0 601 506 1..
W 500
W 270
-1
min 2400
Robert Bosch Power Tools GmbH
-1
min 1500
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
mm 2.8
Assembly
kg 2.7
 Before any work on the machine itself, pull the mains
/II
plug.
Auxiliary Handle (see figure A)
Unscrew the screw 3 out of the auxiliary handle 2 until the
auxiliary handle fits into the auxiliary-handle mount 4.
Slide the auxiliary handle 2 into the auxiliary-handle mount 4.
Tighten the auxiliary handle by turning in clockwise direction.
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
To start the machine, push the On/Off switch 1 forward so
that the "I" is indicated on the switch.
To switch off the machine, push the On/Off switch 1 toward
the rear so that the "0" is indicated on the switch.
To save energy, only switch the power tool on when using it.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools