Product Features; Technical Data; Noise/Vibration Information - Bosch GSG 300 Professional Originalbetriebsanleitung

Product features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) On/off switch
a)
(2) Saw blade guide
a)
(3) Pair of saw blades
(4) Base plate
(5) Handle (insulated gripping surface)
(6) Saw blade guide screw
(7) Cover of the saw blade receptacle
(8) Saw blade receptacle spring lock washer
(9) Saw blade receptacle knurled screw
(10) Base plate screw
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical Data

Foam rubber cutter
Article number
Rated power input
Power output
No-load stroke rate n
0
Stroke speed under load
Stroke
Max. cutting depth
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.

Noise/vibration information

Noise emission values determined according to
EN 62841-2-11.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 81 dB(A); sound power level
92 dB(A). Uncertainty K = 5 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-11:
Cutting with the saw blade 2 607 018 012:
2 2
a = 2.5 m/s , K = 1.5 m/s .
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
Bosch Power Tools
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
u
Selecting saw blades and saw blade guides
Saw blade guides and saw blades of different lengths can be
GSG 300
used depending on the thickness of the material you want to
0 601 575 1.. cut. You can find an overview at the end of this manual.
W 350
Fitting the saw blade guide (see figure A)
W 185
Loosen the two screws (6) and remove them.
−1
min 3500
Position the saw blade guide (2) on the power tool, making
−1
min 2100
sure that the attachment pins fit into the holes provided on
the saw blade guide.
mm 10
Secure the saw blade guide (2) to the power tools using the
mm 300
two screws (6).
kg 1.6
Inserting/replacing saw blades (see figure B)
/II
u
Loosen the knurled screws (9) and remove them together
with the spring lock washers (8) and the cover (7).
Place the pair of saw blades (3) at the bottom of the saw
blade guide (2). Make sure that the elongated slots on the
saw blades fit into the guide pin on the saw blade guide ➊.
Then position the pair of saw blades (3) in the driving pins
➋, making sure that the saw blades sit correctly in the saw
blade guide (2).
Place the cover (7) and the spring lock washers (8) on the
threaded pins on the power tool and secure them with the
knurled screws (9).
Fitting the base plate (see figure C)
Place the saw blade guide (2) in the recess provided on the
base plate (4).
Tighten the screw (10).
Pull the plug out of the socket before carrying out any
work on the power tool.
When fitting or changing the saw blade, wear protect-
ive gloves. Blades are sharp and can become hot when
used for prolonged periods of time.
1 609 92A 83F | (08.07.2022)
English | 11