Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GSA 18V-32 Professional Originalbetriebsanleitung

OBJ_BUCH-2835-002.book Page 17 Tuesday, November 15, 2016 3:41 PM
Switch the machine on and guide it toward the workpiece. Po-
sition the base plate 2 onto the surface of the work and saw
through the material applying uniform contact pressure and
feed. After completing the working procedure, switch the ma-
chine off.
If the saw blade should jam, switch the machine off immedi-
ately. Widen the gap somewhat with a suitable tool and pull
out the machine.
Heavy contamination of the machine can lead to malfunc-
tions. Therefore, do not saw materials that produce a lot of
dust from below or overhead.
Plunge Cutting (see figure E)
 The plunge cutting procedure is only suitable for treat-
ing soft materials such as wood, plaster board or simi-
lar! Do not work metal materials with the plunge cut-
ting procedure!
 Use only saw blades with a maximum length of 100 mm
for plunge cutting. When longer saw blades are used, the
footplate cannot be rested on the workpiece and the pow-
er tool does not have the required hold.
Place the machine with the edge of the footplate 2 onto the
workpiece and switch on. For power tools with stroke speed
control, set the maximum stroke speed. Press the power tool
firmly against the workpiece and allow the saw blade to slowly
plunge into the workpiece.
As soon as the footplate 2 fully lays on the surface of the work-
piece, continue sawing alongside the desired cutting line.
For certain work, the saw blade 1 can also be inserted turned
through by 180° and the sabre saw can be guided accordingly
in a reversed manner.
Flush Cuts (see figure F)
Using elastic bimetal saw blades, items still attached to a wall
(e. g. projecting building elements such as water pipes, etc.)
can be sawn off flush at the wall.
Position the saw blade directly against the wall and apply
some lateral pressure via the tool until the footplate faces
against the wall. Switch the power tool on and saw through
the workpiece, applying constant lateral pressure.
Utility Hook (see figure D)
Your tool is equipped with a utility hook 5 for hanging it, e. g.,
to a ladder, etc. Simply fold out the utility hook 5 to the re-
quired position.
 When the power tool is hung up, take care that the saw
blade is protected from accidental contact. This poses a
risk of injury.
Fold the utility hook 5 back in again when you are ready to
continue working.
Coolant/Lubricant
When sawing metal, coolant/lubricant should be applied
alongside cutting line because of the material heating up.
Recommendations for Optimal Handling of the Battery
Store the battery only within a temperature range between
–20 °C and 50 °C. As an example, do not leave the battery in
the car in summer.
Bosch Power Tools
Occasionally clean the venting slots of the battery using a soft,
clean and dry brush.
A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.
Observe the notes for disposal.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
 For safe and proper working, always keep the machine
and ventilation slots clean.
Clean the saw blade holder preferably with compressed air or
a soft brush. Remove the saw blade from the power tool for
this. Ensure proper operation of the saw blade holder by ap-
plying a suitable lubricant.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
English | 17
1 609 92A 2L0 | (15.11.16)