Werbung
Problem
Blanke steder langs med
en papirkant.
Thank you very much for buying a SHARP laser printer. This manual
tells you how to set up, operate and maintain your new printer,
and contains advice on how to get the best performance from the printer.
The descriptions contained in this manual assume that you are familiar
with the operation of your computer and with how to send files to be printed.
Please use this manual along with the documentation for your computer
hardware and software.
Your new printer has been specially designed to give you high-quality,
trouble-free printing performance. The printer driver software lets the printer
communicate with your computer via an IEEE P1284 bidirectional parallel
interface, so you can control all aspects of printing from the Windows Printer
control panel on your computer screen. Printing speed is a maximum
4 pages per minute at resolutions of 300 x 300 dpi for
the JX-9200 and 600 x 600 dpi for the JX-9210.
Consideration has also been given to ecological and environmental factors.
Your printer features low power consumption, and after printing is
completed it switches to a standby mode which complies with
the US EPA Energy Star program. Moreover, no harmful ozone is
produced during printing, and the toner self-recycling technology
ensures that no toner is wasted. Printer operation is also very
quiet: the printer generates less than 45 dBA of acoustic noise
during printing, and during standby mode the noise level is no
higher than the background noise level.
Despite being packed with so many features, the printer is very compact.
Its footprint is no larger than a single A4 page, and the total weight is
approximately 5 kg, meaning that it is easy to transport and set up. The
100-sheet multipurpose tray is also located at the top of the printer to
save space and to make inserting the paper easy.
Most software applications will let you adjust the margins to have around
the edges of the paper that you will be printing on. The area inside the
margins then becomes the "printable area". The Windows Printer Driver
specifies the minimum values that you can set for these page margins.
These minimum margin settings vary depending on whether you are
printing from a Windows application or from a non-Windows application
in PCL emulation mode.
The following illustration and tables show the minimum settings that can
be made in your software applications in both Windows and PCL modes.
Featuren, lav printopløs-
1
ning, er aktiveret*
Fejlagtig grafik
Halvdelen af papiret er
2
blankt*
Thank you very much for buying a SHARP laser printer. This manual
tells you how to set up, operate and maintain your new printer,
and contains advice on how to get the best performance from the printer.
The descriptions contained in this manual assume that you are familiar
with the operation of your computer and with how to send files to be printed.
Please use this manual along with the documentation for your computer
hardware and software.
Your new printer has been specially designed to give you high-quality,
trouble-free printing performance. The printer driver software lets the printer
communicate with your computer via an IEEE P1284 bidirectional parallel
interface, so you can control all aspects of printing from the Windows Printer
control panel on your computer screen. Printing speed is a maximum
*
1
Udprint med lav opløsning (kun AL-840).
Hvis en side indeholder komplekse grafiker eller der printes forskellige fonts, kan det hænde, at computer-
ens lagerplads ikke er tilstrækkelig. I så tilfælde, aktiverer printerdriveren modien med den lave opløsning,
hvilket automatisk reducerer opløsningen på en kompleks side.
2
*
Problemet optræder kun, hvis kopimaskinen anvendes som printer. (kun AL-840) Se også printerens be-
tjeningsvejledning.
4 – 34
Mulig årsag
TD patronen eller kopitromlen er
ikke installeret korrekt.
Der er åbnet for mange
applikationer.
Opløsningen er sat til 600 dpi.
Toneren er ujævnt fordelt.
Toneren er næsten opbrugt.
Sidens layout er for kompleks.
Opløsningen er sat til 600 dpi.
Indstillingen af papirorienteringen
kan være forkert.
Der er åbnet for mange applikatio-
ner.
Papiret i bakken er måske større
end det specificerede papirformat i
Deres applikation eller printerdriver.
Interface-kablets specifikationer er
måske forkerte.
CPU specifikationerne er måske
forkerte.
Computeren har måske for lidt
random-access-memory (RAM).
Løsning
Kontroller, at TD patronen og
kopitromlen er installeret korrekt.
S. 4-21, 4-22.
Luk alle unødvendige applikationer
før printning.
Indstil opløsningen til 300 dpi.
Tag TD patronen ud og ryst den for-
sigtigt vandret for at fordele toneren
jævnt. S. 4-8
TD patronen skal snart udskiftes.
Forbered en ny TD patron. S. 4-21
Forenkel layoutet for at reducere den
nødvendige lagerplads.
Indstil opløsningen til 300 dpi.
Skift papirorienteringen med printer-
driveren.
Luk alle unødvendige applikationer
før printning.
Læg det korrekte papir i papirbakken.
Benyt interface-kablet, der er leveret
sammen med AL-840.
Kontroller at CPU'en i computeren er
en 486DX 66 Mhz eller bedre.
Installer mere random-access-
memory (RAM) i computeren.
Werbung
Kapitel
