Werbung
Problem
Image voids along a
paper edge
Thank you very much for buying a SHARP laser printer. This manual
tells you how to set up, operate and maintain your new printer,
and contains advice on how to get the best performance from the printer.
The descriptions contained in this manual assume that you are familiar
with the operation of your computer and with how to send files to be printed.
Please use this manual along with the documentation for your computer
hardware and software.
Your new printer has been specially designed to give you high-quality,
trouble-free printing performance. The printer driver software lets the printer
communicate with your computer via an IEEE P1284 bidirectional parallel
interface, so you can control all aspects of printing from the Windows Printer
control panel on your computer screen. Printing speed is a maximum
4 pages per minute at resolutions of 300 x 300 dpi for
the JX-9200 and 600 x 600 dpi for the JX-9210.
Consideration has also been given to ecological and environmental factors.
Your printer features low power consumption, and after printing is
completed it switches to a standby mode which complies with
the US EPA Energy Star program. Moreover, no harmful ozone is
produced during printing, and the toner self-recycling technology
ensures that no toner is wasted. Printer operation is also very
quiet: the printer generates less than 45 dBA of acoustic noise
during printing, and during standby mode the noise level is no
higher than the background noise level.
Despite being packed with so many features, the printer is very compact.
Its footprint is no larger than a single A4 page, and the total weight is
approximately 5 kg, meaning that it is easy to transport and set up. The
100-sheet multipurpose tray is also located at the top of the printer to
save space and to make inserting the paper easy.
Most software applications will let you adjust the margins to have around
the edges of the paper that you will be printing on. The area inside the
margins then becomes the "printable area". The Windows Printer Driver
specifies the minimum values that you can set for these page margins.
These minimum margin settings vary depending on whether you are
printing from a Windows application or from a non-Windows application
in PCL emulation mode.
The following illustration and tables show the minimum settings that can
be made in your software applications in both Windows and PCL modes.
Low resolution print fea-
ture is activated*
1
.
Faded graphics
Half of the page is
blank*
2
.
Thank you very much for buying a SHARP laser printer. This manual
tells you how to set up, operate and maintain your new printer,
and contains advice on how to get the best performance from the printer.
The descriptions contained in this manual assume that you are familiar
with the operation of your computer and with how to send files to be printed.
Please use this manual along with the documentation for your computer
hardware and software.
Your new printer has been specially designed to give you high-quality,
trouble-free printing performance. The printer driver software lets the printer
communicate with your computer via an IEEE P1284 bidirectional parallel
interface, so you can control all aspects of printing from the Windows Printer
control panel on your computer screen. Printing speed is a maximum
1
*
Low resolution print (AL-840 only)
If a page including complex graphics or various kinds of fonts is printed, the computer resource may be in-
sufficient. In this case, the printer driver activates the low resolution printing feature which automatically
lowers the resolution of a complex page.
2
*
The problem occurs only if the copier is used as a printer. (AL-840 only) See also the printer operation
manual.
Possible cause
TD cartridge or drum cartridge not
installed properly.
There may be too many applica-
tions open.
Resolution is set to 600 dpi.
Toner may be unevenly distributed.
Toner is low.
The page layout is too complex.
Resolution is set to 600 dpi.
Page orientation setting may be
incorrect.
There may be too many applica-
tions open.
The paper in the tray may be larger
than the paper size specified in your
application or printer driver.
Interface cable specifications may
be incorrect.
The CPU specifications may be
incorrect.
The computer may have insufficient
random-access memory (RAM).
Solution
Ensure that the TD cartridge and
drum cartridge are installed properly.
p. 3-21, 3-22
Close all unnecessary applications
before printing.
Set resolution to 300 dpi.
Remove the TD cartridge and gently
shake it horizontally to evenly distrib-
ute toner. p. 3-8
TD cartridge must be replaced soon.
Prepare a new TD cartridge. p. 3-21
Simplify the page layout to reduce
required memory.
Set resolution to 300 dpi.
Change the page orientation with the
printer driver.
Close all unnecessary applications
before printing.
Load the correct paper into the paper
tray.
Use the interface cable included with
the AL-840.
Check that the CPU of your computer
is 486DX 66 MHz or better.
Install more random-access memory
(RAM) in your computer.
3 – 31
Werbung
Kapitel
