Technical Specifications - Hudora 74501 Aufbau- Und Bedienungsanleitung

instructions on Assembly And use
EN
congrAtulAtions on purcHAsing tHis product!
Please read these instructions carefully. The instructions are an integral component of
the product. Therefore, please store them and the packaging carefully in case questions
arise in the future. Please always include these instructions when giving the product to
a third party. This product must be assembled by an adult. This product is not designed
for industrial use. The use of the product requires certain capabilities and skills. Always
adjust according to the age of the user and use for the purpose it has been designed for.

tecHnicAl specificAtions

Item: Punching Ball
Item number: 74501
Adjustable height: 100 to 130 cm
Weight: 2.7 kg
If you have assembly problems or would like further information on the product, we have
all you need and more at http://www.hudora.de/artnr/74501/.
sAfety instructions
Although the box set is designed for children, it is not a toy. Please check that the equip-
ment has no technical faults; in the case of damage or lose connecting elements don't use
the product anymore. Adjustments to the product or use of non-original parts can lead to
accidents. The set is not stable unless sufficient ballast is used. Before training, please
fill the set with sufficient water or sand and check stability. Before use chose a location
for training with sufficient space, so that no damage can be caused to persons or other
objects. We advise that the set is stored in a dry and dark place. When necessary clean
your set using a slightly damp cloth. Moisture on the metal parts of the equipment can lead
to rust and should therefore be avoided. Boxing gloves of a suitable size should always
be worn during training. Please also protect the enclosed gloves from moisture. After use
we advise that the gloves are kept in a dry and well ventilated place. Please only use the
gloves for the punch ball. They are not designed for real boxing matches.
putting togetHer
Step 1:
Remove all parts from the packaging. Next pump up the ball (10). To do this screw the val-
ve adapter (11) on to the pump and pierce the valve on the ball. Pump until the ball is hard
(not too hard otherwise it could burst. If the ball is too hard boxing can become painful!)
Remove the pump and keep it safe, as the ball could lose pressure over time. If you wish
to deflate the ball, simply pierce the valve using the valve adapter.
Step 2:
Next, screw the ball onto the telescopic tube (9). For best mounting, two different screws
should be used to fix the ball in place. For the lower cross screw, make sure the inner
tube is screwed in in such a way that the borehole is completely open and the screw can
penetrate easily. Following this, bolt the cross screw together with a cap nut and two lock
washers. Another smaller screw must then be screwed into the upper hole.
Step 3:
Now it is time for the base: Is the plastic sleeve already on the spring (7)? If not, first place
it over the spring so that no hair or fingers can get caught in the spring thread. Then place
the metal plate with the hole (5) in it over the pipe with the spring (7) as shown in the pic-
ture. Now insert the guide sleeve (2) into the base (1) from above and push the tube with
the spring (7) through along with the metal disc (5). Mount another guide sleeve (2) and a
centering plate (4) before fixing the entire construction with the Allen key (6).
Step 4:
A suitable key is provided to tighten the Allen screw. The screw has a type of glue on the
thread and is therefore more difficult to tighten. This is to prevent it from becoming lose.
If the screw is tightened often it can cause wear and become unsafe, which would require
the screw to be replaced. Now place the standpipe (8) on top; it fits into the spring knob
on the spring pipe. Finally tighten the telescopic pipe (9). To do this loosen the screw on
the standpipe and slide the pipes into each other. The middle of the ball can now be set to
a height between 900 and 1150 mm. There are markings 50mm from the bottom end of
the telescope pipe. The pipe must not be lifted further than these markings, as the clamp
would then no longer be safe. Make sure that clamping screw is screwed tight during use
so that the ball cannot move on its own.
Step 5:
Now fill the base with sand, gravel or water and place the cap (3) on the opening. If you
decide to fill the punch ball with water, make sure that you only use it on surfaces which
are not water-sensitive!
mAintenAnce And storAge
Use a dry or damp cloth only to clean the product; do not use special cleaning agents! Check
the product for damage or traces of wear and tear before and after each use. Do not make
any structural changes. For your own safety, please use original spare parts only. These can
be sourced from HUDORA. If parts become damaged or if sharp edges or corners should
develop, the product may not be used any more. If in any doubt, please contact our service
team (http://www.hudora.de/service/). Store the product in a safe place where it is protec-
ted from the elements, cannot be damaged, and cannot injure anyone.
disposAl AdVice
At the end of the product's life, please dispose of it at an appropriate collection point provi-
ded in your area. Local waste management companies will be able to answer your questions
on this.
serVice
We make every effort to deliver faultless products. If faults do arise however, we put just
as much effort into rectifying them. Therefore, you can find numerous information on the
product, replacement parts, solutions to problems and lost assembly manuals at http://
www.hudora.de/artnr/74501/.
spAre pArts And originAl Accessories AVAilAble At:
http://www.hudora.de/artnr/74501/
4/8