Applying Effects To Only A Monitor Signal - Yamaha MT400 Bedienungsanleitung

32

Applying Effects to Only a Monitor Signal

Using a direct recording and the monitor select switch enables you to apply effects to only a
monitoring signal while recording the unprocessed sound on a track. For example, you can
record a dry vocal on a track, while monitoring the vocalist with reverb effects applied. This
section explains how to record a vocal to Track 4 while monitoring Tracks 1–3 as an example.
7
6
3
1
Connect AUX SEND 1 to the input of the
effects processor, and connect the outputs of
the effects processor to STEREO INPUTs 5L
and 6R. Set the effects processor so that it will
output only the processed signal.
2
Connect a vocal microphone to MIC/LINE
INPUT 4.
3
Set the [INPUT-FLIP] switches on Input
Channels 1–4 to "MIC/LINE (
4
Set the [REC SELECT] switches on Tracks 1–3
to "OFF".
5
Set the [REC SELECT] switch on Track 4 to
" ".
4
The vocal will be directly recorded on Track 4.
—Owner's Manual
2
4
3
1 2 3 4
GAIN GAIN GAIN GAIN
LINE MIC LINE MIC LINE MIC LINE MIC
HIGH HIGH HIGH HIGH
–12 +12 –12 +12 –12 +12 –12 +12
MID MID MID MID
–12 +12 –12 +12 –12 +12 –12 +12
LOW LOW LOW LOW
–12 +12 –12 +12 –12 +12 –12 +12
AUX AUX AUX AUX
1 1 1 1
0 10 0 10 0 10 0 10
AUX AUX AUX AUX
2 2 2 2
0 10 0 10 0 10 0 10
MIX CUE MIX CUE MIX CUE MIX CUE
0 10 0 10 0 10 0 10
MIC/LINE TAPE MIC/LINE TAPE MIC/LINE TAPE MIC/LINE TAPE
to L to R to L to R
MIC/ MIC/ MIC/ MIC/
TAPE TAPE TAPE TAPE
LINE LINE LINE LINE
INPUT-FLIP INPUT-FLIP INPUT-FLIP INPUT-FLIP
PAN PAN PAN PAN
L R L R L R L R
10 10 10 10
9 9 9 9
8 8 8 8
7 7 7 7
6 6 6 6
5 5 5 5
4 4 4 4
3 3 3 3
2 2 2 2
1 1 1 1
0 0 0 0
)".
1
STEREO INPUT
5 6 7 8
L R L R 1
2
5 –6 7 –8
L R L R
LEVEL LEVEL
+6
+3
0 10 0 10
0
–5
–10
REC
MULTITRACK CASSETTE RECORDER
1 2
L R
TAPE SPEED CONTROL REC SELECT
PITCH
1 2 3
OFF OFF OFF
L R L
4.8/ 9.5
+
–
ZERO STOP
ON ON
OFF OFF
SYNC
NOISE REDUCTION SYSTEM
MONITOR/PHONES
LEVEL
STEREO
ST+CUE
CUE
MIN MAX
STEREO
10
9
8
7
6
5
4
3
2
1
0 REC PLAY REW
6
Turn up the CUE controls on Input Channels
1–4.
You can monitor playback on Track 1–3 and record
the source (the vocal without effects) to Track 4 via
the CUE bus.
7
Turn up the AUX 1 control on Input Channel
4.
The vocal signal is sent to the effects processor
connected to the AUX SEND 1 jack.
8
Turn up the LEVEL control for stereo inputs
5L/6R.
The processed vocal signal is sent to the Stereo bus.
9
Set the monitor select switch to "ST+CUE".
Now you can monitor the CUE bus signals (tape
Tracks 1–3 and the dry vocal) mixed with the Stereo
bus signal (processed vocal).
8
+6
POWER
+3
0
–5
–10
4
3 4
METER SELECT
4 4TR
OFF STEREO
R
5
9
FF STOP PAUSE