Stopping The Motor - Brill Brillencio 43 BRe-comfort Gebrauchsanweisung

Disposal of Brill power pack
A12(e)
Please refer to Waste disposal /
Recycling
7.3.2 Start-up of the Brill power
pack A12(e)
Pull the plug-in connector (fig. P
Pos. 4) out of the charging port
(fig. O Pos. 1) on the Brill Power
pack A12(e). Plug the Brill Power
pack A12(e) in the support provid-
ed for this purpose (fig. N Pos. 17)
until you feel the Brill Power pack
A12(e) click into place. You can
detach the Brill Power pack A12(e)
from the appliance by pushing the
locking lever (fig. N Pos. 16) down
and pulling the Brill Power pack
A12(e) out.
When the appliance is active,
the Brill Power pack A12(e) will
heat up. This is normal and does
in no way deteriorate device
output.
7.3.3. Electric start-up
Press down the safety hoop (fig. N
Pos. 5) towards the guiding rod
system. Plug in ignition key (fig.N
Pos. 18) and turn to START (ON)
position. Activate the starter for
8. Information concerning correct mowing
8.1. General Information about
Lawn Care
We recommend mowing your lawn
every week if possible to keep
your lawn looking its best. Mowing
your lawn regularly strengthens the
individual blades of grass and
makes your lawn more resistant.
Short grass cuttings (up to around
1 cm in length) can be left on the
lawn after mowing. Longer cuttings
should be removed so that the lawn
does not turn yellow and become
matted. If you do not attach the
grass catcher when mowing, the
brillencio lawnmower distributes
the grass cuttings cleanly from the
high rear ejection chute.
5 seconds maximum. Once the mo-
tor has started, release the ignition
key. It will automatically turn to the
OPERATIVE ( I ) position.
After starting, put the accelerator
from Start to Max.
The Power pack is automatically
recharged during operation.

7.4. Stopping the Motor

You can stop the engine by
releasing the safety handle
(Figure A Pos. 5). An integrated
brake stops the cutting tool
rotating within 3 seconds.
7.5. Putting the Rear Wheel Drive
into Operation (43 BR(e)-comfort
and 48 BR(e)-comfort)
Figure I Pos. 9
To engage the rear wheel drive,
pull the coupling link for the
wheel drive (Figure I, Pos. 9)
upwards towards the guide
handle. Release the coupling link
(Figure I, Pos. 9) to deactivate
the wheel drive.
Cut your lawn for the first time in
the spring as soon as the grass be-
gins to grow and you can walk on
the lawn. If the grass has already
grown too tall, first mow in one
direction with a high cutting height
then mow at right angles to the first
cut with the required shorter cutting
height.
8.2. Mowing
Only mow with sharp, unworn
blades so that the blades of grass
are not frayed and the lawn does
not turn yellow.
The cutting height should always
be at least 3 – 4 cm since the lower
part of the grass blade is white.
If you cut the grass too short, the
7.6. Putting the Vario Wheel Drive
into Operation (Vario wheel drive
with 51 BR(e)-comfort only)
These lawnmowers are equipped
with a vario gearbox. You can
select the speed at which you mow
the lawn (between 3 km/h and
5,5 km/h). You can only change
the speed when the motor is run-
ning and the lawnmower is moving.
To adjust the speed, move the lever
(Figure I, Pos. 6) in the relevant
direction (slow fast).
To engage the wheel drive, pull up
the coupling link for the wheel drive
(Figure I, Pos. 9) towards the guide
handle.
Release the coupling link (Figure I,
Pos. 9) to disengage the wheel drive.
Warning! Do not remove
A
or bridge the safety devices
installed on this lawnmower by
the manufacturer otherwise there is
a risk of injury and the lawnmower
motor will no longer switch off
automatically.
Warning! The cutting tool
A
continues to rotate for
a short time after switching off the
motor!
lawn will no longer appear lush
and green. The blades of grass will
also dry out too quickly above all
in the summer.
To achieve a clean cut, always
guide your lawnmower at an
appropriate speed in straight
cutting paths. The paths should
always overlap by a few centi-
metres so that you do not miss
strips of lawn.
Never lift or carry the lawnmower
when the motor is running.
If you encounter a foreign body,
switch off the motor and unplug the
spark plug connector. Check for
damage to the lawnmower and car-
ry out all necessary repairs before
GB
23