Krups Precision range XP80 Bedienungsanleitung Seite 7

b) The Coffee Grinder
Regularly cleaning the grinder and the grinder outlet with the cleaning brush is important to
ensure long life of your machine.
IMPORTANT: When cleaning the grinder, please make sure there are no beans in the bean hopper.
To remove the last beans in the grinder, press the START/STOP GRIND button (19), wait for the last
coffee ground to go out and press again the button to stop.
WARNING: Please unplug the machine before cleaning the grinder (4)
1. Rotate the bean box anti-clockwise to remove the bean box, by aligning the following arrow
marked on the bean hopper with the orange index on the machine (12).
2. Turn the internal grinding wheel anti-clockwise and take it out (41). Use the cleaning brush
to clean the grinding wheel and remove the ground coffee in the gears (43). Please note that
the grinding wheel cannot be directly rinsed with water (only with the brush).
3. Use the cleaning brush to clean the grinding chamber and the ground coffee channel (44).
4. Do not install the grinding wheel at this time, re-install the empty bean hopper (46).
5. Plug the machine, press the power button and press the START/STOP GRIND button (19), let
the grinder run to sweep out the coffee ground residue in the grinding chamber. (If coffee
ground inside is not removed completely, please repeat step 3 and 4).
6. Turn off and unplug the machine.
7. Remove the bean hopper anti-clockwise (4).
8. Install the grinding wheel securely in position (45).
9. Install the bean hopper back on the machine (46).
Cleaning is completed.
c) The brewing head
Daily cleaning
After your coffee extraction, clean your coffee brewing head with a flush: remove your portafilter,
remain on coffee recipes on the 'Recipes Dial' and press the START/STOP BREW button (8). Press
again after a few seconds to stop.
You can also clean the brewing head with brush after each extraction.
Regular cleaning:
Please rinse the coffee brewing head regularly as following steps:
1. Insert 2-cup single wall filter into the portafilter (9).
2. Put the blind sieve in the filter so that the holes of the filter are hidden (47).
3. Insert the portafilter into the brewing head (25).
4. Select Espresso, then press START/STOP BREW (8) button to start rinsing process (about 30
seconds), rinsed water goes directly into the drip tray.
5. Rinsing process stops automatically. Remove the portafilter and the blind sieve. Empty the
portafilter if some hot water remains.
6. Empty the drip tray when it is full (48).
7. START/STOP BREW indicator becomes orange fix, press the START/STOP BREW button to
return normal (8).
d) The water circuit
Please clean the coffee and steam water circuit once every 3 months:
1. Remove and empty the drip tray (48), then reposition it in the machine.
2. Insert 2-cup filter into the portafilter (9).
3. Put the blind sieve in the filter so that the holes of the filter are hidden.
4. Place one KRUPS cleaning tablet* on the blind sieve (50).
5. Insert the portafilter into the brewing head (25).
6. Select CALC on the RECIPES AND CLEANING DIAL (51).
8
7. Press START/STOP BREW button (8) and hold down for 3 seconds to start cleaning process.
The water used for cleaning goes directly into the drip tray. It lasts about 3 minutes.
8. Remove the portafilter. Check if the tablet is dissolved completely. If not, please repeat the
point 5, 6 and 7.
Note: *The KRUPS Cleaning Tablet XS3000 can be purchased on the Krups official website or other
retailers.
DESCALING THE MACHINE
When the CALC indicator red light is on, you need to descale your machine. You can start descaling
at any time. Make sure the portafilter is not inserted to the machine.
1. Remove and empty the drip tray (48), then reposition it in the machine.
2. Empty the water tank (54). Remove the filter if present (you can re-insert it at the end of the
descaling process) (55).
3. Put the KRUPS Descaler* into the water tank (56) and add 500ml / 17.5 oz of water. Put a
container (1L / 34 oz) on the drip tray under the coffee outlet, hot water outlet and under the
steam wand (6).
4. Turn the RECIPES AND CLEANING dial to CALC.
5. Press the START/STOP BREW button to start descaling process (8).
6. Water comes out from each outlet (Brewing head for 2 min 30 sec, Hot water outlet for 2 min
30 sec, Steam outlet for 2 min 30 sec). This cycle repeats automatically one more time.
7. START/STOP BREW button indicator is blinking white. The Descaling is finished now, proceed
to rinsing.
8. Empty the container (57). Remove the water tank, empty out any residual descaler solution
(54), rinse under running water and fill with fresh water (1L/34 oz). Put the water tank and
the container back on the machine.
9. Press START/STOP BREW button (8).
10. Water comes out from each outlet (Brewing head for 30 sec, Hot water outlet for 30 sec,
Steam outlet for 30 sec). This cycle repeats automatically one more time.
11. Once finished rinsing process, START/STOP BREW button light and Power button light
become fixed white.
12. Empty the container (57), remove the water tank, fill with fresh water and reposition it in the
machine. If present, re-set water filter.
13. Turn the RECIPES AND CLEANING dial to one of the beverages.
The machine is now ready for use.
To exit DESCALING MODE halfway, press the POWER button (9). This does not clear the descaling
alert.
Note: *The KRUPS Descaler can be purchased on the Krups official website or other retailers.
9