Emergency Calling Via Voip; Switching A Call From Headset To Desk Telephone Handset; Switching A Call From Desk Telephone Handset To Headset; New Master Headset Pairing To Base - Jabra GN9330e USB Anleitung

Important: Steps 2 to 4 may be repeated twice for 2 more secondary headset participants.
6. Use the primary headset's telephone/VoIP application to dial desired number and initiate
conference call.
At any point during a call in progress, you may add secondary headsets to form a conference call.
A maximum number of 4 headsets (1 master plus up to 3 secondary) may join a conference call.
Ending conference calls for all participants
1. Place primary headset in its base, or press its talk button.
–> The conference call is now terminated for all participants.
Note: If the conference call was made via VoIP, you may need to perform additional steps to end
your call. See your VoIP application's user instructions.
Ending conference calls for a secondary headset only
1. Place secondary headset in its own base, or press its talk button.
–> This participant is now terminated from the conference call.
GN9350e GN9330e GN9330e USB
4.4 Emergency calling via VoIP
Your headset supports quicker emergency calling via VoIP applications (softphone).
If the headset is connected to a PC and the PC is screensaver-locked, you can still use the
headset to dial emergency services.
To call emergency services via VoIP:
1. Put on headset.
2. If the PC is on (even if screensaver-locked), press the base unit's telephone mode button
and USB mode button simultaneously for 5 seconds.
–> The base will automatically dial the emergency services number.
Note: This emergency services feature works only with certain VoIP applications.
Please refer to www.jabra.com for more information.
GN9350e GN9330e GN9330e USB
4.5 Switching a call from headset to desk telephone handset
It's possible to switch a call in progress from the headset to the telephone's handset:
1. Lift the telephone's handset to your ear.
2. Do one of the following:
• Place the headset into the charging cradle.
12
• Press the headset's talk button.
• Press the base's telephone mode button.
–> The headset's link indicator will stop flashing to indicate that the headset-base link
has been closed.
Important: If using electronic hookswitch on your telephone, do not place the headset into
the charging cradle, and do not press the headset´s talk button or press the base´s telephone
mode button, as this will disconnect the call.
If the headset runs out of battery power, the headset-base link will remain active for up to 2
minutes to allow for battery changing.
GN9350e GN9330e GN9330e USB
4.6 Switching a call from desk telephone handset to headset
It's possible to switch a call in progress from the telephone's handset to the headset:
1. Remove the headset from base, or if already out, press
the headset's talk button. This establishes a link.
–> The headset's link indicator will start flashing and the
call will be switched to the headset.
Note: Do not place handset before the call is over, as this will end the call.
GN9350e GN9330e GN9330e USB
4.7 New master headset pairing to base
You may designate a new master headset for your base.
Important: Before designating a new master headset, ensure
that the original headset's link to the base unit is closed by
pressing its talk button. The telephone or USB indicator should
not flash.
To designate a new master headset:
1. Place the new master headset into the charging cradle of
the base.
2. Press the base's pairing button.
–> Both the telephone and USB mode buttons on the
base, and the headset's link indicator, will light for 2 sec-
onds. This indicates successful pairing of the new master
headset.
2
13
1