Mitsubishi Electric Mr.SLIM SEZ-M71DAL2 Installationshandbuch Seite 4

6
[Fig. 6-1]
ⓐ
[Fig. 6-2-1]
ⓑ
ⓐ
90˚
ⓐ Copper tubes ⓒ No good
ⓑ Good ⓓ Tilted
[Fig. 6-2-4]
ⓐ
ⓑ
ⓒ
ⓐ Flaring tool ⓓ Flare nut
ⓑ Die ⓔ Yoke
ⓒ Copper tube
[Fig. 6-3-2]
Ⓑ
Ⓐ
Ⓒ
Ⓔ
Ⓐ Pipe cover (small) (accessory)
Ⓑ Caution:
Pull out the thermal insulation on the refrigerant piping at
the site, insert the flare nut to flare the end, and replace the
insulation in its original position.
Take care to ensure that condensation does not form on
exposed copper piping.
Ⓒ Liquid end of refrigerant piping
[Fig. 6-5-1]
Ⓐ
Ⓑ
Ⓒ
Ⓓ
Ⓐ Downward slope 1/100 or more
Ⓑ Connection dia. R1 external thread
Ⓒ Indoor unit
Ⓓ Collective piping
Ⓔ Maximize this length to approx. 10 cm
4
øB
øA
[Fig. 6-2-2]
ⓒ
ⓓ ⓔ ⓕ
ⓔ Uneven
ⓕ Burred
[Fig. 6-2-5]
A
ⓔ
ⓑ
ⓓ
ⓒ
Ⓔ
Ⓓ
Ⓕ
ⒶⒼ
Ⓖ
①
Ⓒ Ⓒ
Ⓔ
②
6.1
ⓑ
SEZ-M25, 35
SEZ-M50
ⓐ Indoor unit
SEZ-M60
ⓑ Outdoor unit
SEZ-M71
6.2
ⓑ
ⓐ
ⓒ
ⓓ
ⓐ Burr ⓒ Spare reamer
ⓑ Copper tube/pipe ⓓ Pipe cutter
ⓐ ⓑ
ⓓ ⓔ ⓕ
ⓒ
ⓘ
ⓐ Smooth all around ⓔ Tilted
ⓑ Inside is shining without
ⓕ Scratch on flared plane
any scratches
ⓖ Cracked
ⓒ Even length all around
ⓗ Uneven
ⓓ Too much
ⓘ Bad examples
Ⓗ
Ⓜ
Ⓛ
Ⓕ
Ⓗ
Ⓛ
Ⓓ Gas end of refrigerant piping
Ⓔ Site refrigerant piping
Ⓕ Main body
Ⓖ Pipe cover (large) (accessory)
Ⓗ Thermal insulation (field supply)
Ⓘ Pull
Ⓙ Flare nut
Ⓚ Return to original position
6.5
[Fig. 6-5-2]
Ⓐ
Ⓐ Indoor unit
Ⓑ Pipe cover (short) (accessory)
Ⓒ Tie band (accessory)
Ⓓ Band fixing part
Ⓔ Insertion margin
Model A
9.52
12.7
15.88
15.88
[Fig. 6-2-3]
ⓐ Flare nut
ⓑ Copper tube
[Fig. 6-3-1]
ⓖ ⓗ
Ⓙ
Ⓘ
Ⓞ
Ⓙ
Ⓛ
Ⓚ
Ⓛ Ensure that there is no gap here
Ⓜ Plate on main body
Ⓝ Band (accessory)
Ⓞ Ensure that there is no gap here. Place join upwards.
Ⓘ
Ⓑ
Ⓕ
5 25 Ⓗ
Ⓔ
Ⓓ
Ⓒ
Ⓕ Drain hose (accessory)
Ⓖ Drain pipe (O.D. ø32 PVC TUBE,
field supply)
Ⓗ Insulating material (field supply)
Ⓘ Max.145 ± 5 mm
B
6.35
6.35
6.35
9.52
ⓐ
ⓑ
6.3
Ⓝ
20
20
Ⓞ
20
20
Ⓝ
Ⓖ