EINHELL TE-MS 216 T Originalbetriebsanleitung Seite 33

screws (41).
•
Fasten the splitter (40) by using the hex key
(49) to tighten the two socket head screws
(41).
•
Make sure that the splitter (40) is fitted
straight and does not wobble.
•
The splitter (40) must be positioned in the
center along an imaginary line extending be-
hind the blade (6) so that it is not possible for
the cut material to get jammed.
•
The gap between the blade (6) and the split-
ter (40) should measure 3 to 8 mm. (See Fig.
18)
•
To dismantle, proceed in reverse order.
5.7 Connection for a sawdust extractor
(Fig. 19/20)
A connection for extracting the sawdust is provi-
ded with the extractor socket for crosscut mode
(28) and with the extractor socket for table mode
(47). (Diameter information can be found in sec-
tion 4 Technical data)
In crosscut mode (Fig. 19):
•
Fasten the extractor adapter (29) to the ext-
ractor socket (28) on the back of the machine.
•
Then connect, for example, a wet&dry vac to
the extractor adapter (29).
In table mode (Fig. 20):
•
Fasten the extractor adapter (29) to the ext-
ractor socket (47) on the side of the machine
head (1).
•
Then connect, for example, a wet&dry vac to
the extractor adapter (29).
6. Operation and fi ne adjustment
Set the saw to crosscut mode (see 5.2).
6.1 Adjusting the crosscut saw (Fig. 1 – 3, 21)
•
To adjust the turntable (12) slacken the lo-
cking screw (15) by approx. 2 turns. Only then
is it possible to adjust the turntable while hol-
ding the release button (14) pressed down.
•
Turn the turntable (12) and scale pointer (17)
to the desired angular setting on the scale
(16). (See Fig. 21)
•
The saw has locking positions at angles of
-45°, -31.6°, -22.5°, -15°, 0°, 15°, 22.5°, 31.6°
and 45°, at which the turntable (12) audibly
clicks into position. Once the turntable is en-
gaged, the setting must be additionally secu-
Anl_TE-MS_216_T_SPK13.indb 33
GB
red by tightening the locking screw (15).
•
If different angle settings are required, the
turntable (12) must be secured in position by
using only the locking screw (15).
•
The machine head (1) can be lowered by
pressing the release button (2).
•
You can tilt the machine head (1) to the left
by up to 45° when the locking grip (22) is re-
leased.
•
After the angle selected with the pointer
(24) on the scale (23) is reached, secure the
machine head (1) again with the locking grip
(22). (See Fig. 21)
6.2 Precision adjustment of the stop rail
(Fig. 22/23)
•
Lower the machine head (1) and fasten in
place with the retaining pin (33).
•
Fasten the turntable (12) in 0° position.
•
Place the 90° stop angle (a) between the bla-
de (6) and the stop rail (10).
•
Slacken the four socket head screws (11)
using the hex key (49), set the stop rail (10) to
90° in relation to the blade (6), and retighten
the socket head screws (11).
•
Finally, check the position of the pointer (17).
If necessary release the pointer (17) with a
crosstip screwdriver, move it to the 0° positi-
on on the scale (16), and fasten the pointer
again.
•
There is no angle stop (a) or crosstip
screwdriver supplied with this product.
6.3 Precision adjustment of the angle stop
for 90° crosscuts (Fig. 24/25)
•
Lower the machine head (1) and fasten in
place with the retaining pin (33).
•
Fasten the turntable (12) in 0° position.
•
Undo the locking grip (22) and tilt the machi-
ne head (1) to the right to 0° using the handle
(3).
•
Place the 90° angle stop (a) between the bla-
de (6) and the turntable (12).
•
Slacken the lock nut (27) and adjust the ad-
justment screw (25) until the angle between
the blade (6) and the turntable (12) equals
90°.
•
Retighten the lock nut (27) to secure this set-
ting.
•
Finally, check the position of the pointer (24).
If necessary release the pointer (24) with a
crosstip screwdriver, move it to the 0° position
on the scale (23), and fasten the pointer (24)
again.
•
There is no angle stop (a) or crosstip
- 33 -
10.05.2023 14:54:00