Scheppach cs 45 Originalbetriebsanleitung Seite 14

INSTRUCTIONS FOR ALL SAWS
• Do not use a sanding belt.
• Make sure that the dust catching mechanism is cor-
rectly installed, as is described in this manual.
• Wear breathing protection.
• Only those saw blades recommended in the manual
should be used.
• Always wear ear protection.
• Replace the saw blades as described in this manual.
• The maximum cut depth is 45 mm.
If the electrical cable of this tool is damaged it must be
replaced by the manufacturer or the customer service
department or a similarly qualified specialist in order to
avoid dangers.
FURTHER SPECIAL SAFETY INSTRUCTIONS FOR
CIRCULAR SAWS
a) Only use the recommended saw blades which corre-
spond to EN 847-1.
b) Do not use sanding belts.
c) Only use the manufacturer's original saw blades with
the number Ø 145 mm, 5500/min, 145 x 20 x 2.4.
Do not use any saw blades which do not correspond to
the characteristics described in these operating instruc-
tions. Saw blades may not be brought to a stop by pres-
sure on the machine from the side.
Make sure that the saw blade is tightly assembled and
turns in the correct direction.
m Special Safety Instructions
Safety instructions for circular saws
- Hold the equipment on the insulated handles, when
you undertake work in which the tool being used could
come into contact with hidden electrical wires, or its own
cable. Contact with a live power source can electrify the
metal parts of the tool and lead to an electrical shock.
m Proper use
CE tested machines meet all valid EC machine guidelines as
well as all relevent guidelines for each machine.
• The machine must only be used in technically perfect
con dition in accordance with its designated use and
the in structions set out in the operating manual, and
only by safety-conscious persons who are fully aware of
the risks involved in oerating the machine. Any func-
tional dis orders, especially those affecting the safety of
the machine, sholud terefore be rectified immediately.
• Any other use exceeds authorization. The manufacturer
is not responsible for any damages resulting from un-
authorized use; risk is the sole responsibility of the
operator.
• The safety, work and maintenance instructions of the
manufacturer as well as the technical data given in
the calibrations and dimensions must be adhered to.
• Relevant accident prevention regulations and other,
gene rally recognized safety-technical rules must also
be adhered to.
14
• The machine may only be used, maintained, and op-
erated by persons familiar with it and instructed in its
operation and procedures. Arbitrary alterations to the
machine release the manufacturer from all responsi-
bility for any resulting damages.
• The machine may only be used with original accesso-
ries and tools made by the manufacturer.
• The machine may not be operated with sanding belts.
m Remaining hazards
The machine has been built using modern technology in
accor dance with recognized safety rules. Some remaining
hazards, how ever, may still exist.
• The use of incorrect or damaged mains cables can lead
to injuries caused by electricity.
• Even when all safety measures are taken, some re-
maining hazards which are not yet evident may still
be present.
• Remaining hazards can be minimized by following the
instructions in „Safety Precautions", „Proper Use" and
in the entire operating manual.
• Do not force the machine unnecessarily: excessive
cutt ing pressure may lead to rapid deterioration of the
blade and a decrease in performance in terms of finish
and cutting precision.
• When cutting aluminium and plastics always use the
app ro priate clamps: all workpieces must be clamped
down firmly.
• Avoid accidental starts: do not press the start button
while inserting the plug into the socket.
• Always use the tools recommended in this manual to
obtain the best results from your plunge cut saw.
• Always keep hands away from the work area when the
ma chine is running; before performing tasks of any
kind release the main switch button located on the
handgrip, thus disconnecting the machine.
m Suitable use
To cut:
• Hard and soft, domestic and exotic wood both longitu-
dinally and transversally and with appropriate adjust-
ments (specific blade and clamps);
Unsuitable use
Do not cut:
• Ferrous materials, steel and cast iron or any other ma-
terial not mentioned above and in particular foodstuffs.
Start-up
Observe the safety notes in the operating instructions before
operating the machine.
REMOVAL OF PACKAGING
Remove the box used to protect the machine during
trans portion and keep it intact for future transportation
and storage.