Kawai MP9500 Bedienungsanleitung Seite 59

3.2.3 Zone 1-4 External DATA
No. PARAMETER
1 K.range_lo
2 K.range_hi
3 velo_sw_type
4 velo_sw_value
5 velo_sense
6 transpose
7 part_sw
8 damper_sw
9 FSW_sw
10 EXP_sw
11 modwheel_sw
12 bender_sw
13 tx_ch
14 tx_prog_sw
15 tx_prog_no
16 tx_bank_sw
17 tx_bank_lo
18 tx_bank_hi
19 tx_level_enable_sw
20 tx_level_sw
21 tx_level
22 tx_knobA_sw
23 tx_knobA_no
24 tx_knobA_value
25 tx_knobB_sw
26 tx_knobB_no
27 tx_knobB_value
28 tx_knobC_sw
29 tx_knobC_no
30 tx_knobC_value
31 tx_knobD_sw
32 tx_knobD_no
33 tx_knobD_value
34 panpot
35 dummy
36 finetune
37 rev_send
38 efx_send
39 bend_range
40 cutoff
41 attack
42 decay
43 release
44 solo_sw
45 solo_mode;
46 tx_pan_sw;
47 dummy
48 tx_fine_sw;
49 tx_bendrange_sw;
50 tx_cutoff_sw;
51 tx_attack_sw;
52 tx_decay_sw;
53 tx_release_sw;
VALUE
0 ~ 127 (C-2 ~ G8)
0 ~ 127 (C-2 ~ G8)
0 ~ 2 (off, loud, soft)
0 ~ 127
0 ~ 64 ~ 127 (-64 ~ 0 ~ +63)
28 ~ 64 ~ 100 (-36 ~ 0 ~ +36)
0,1 (off, on)
0,1 (off, on)
0,1 (off, on)
0,1 (off, on)
0,1 (off, on)
0,1 (off, on)
0 ~ 15 (1 ~ 16ch)
0,1 (off, on)
0 ~ 127(1 ~ 128)
0,1 (off, on)
0 ~ 127
0 ~ 127
0, 1 (off, on) *use only single mode
0, 1 (off, on)
0 ~ 127
0,1 (off,on)
0 ~ 114
0 ~ 127
0,1 (off, on)
0 ~ 114
0 ~ 127
0,1 (off, on)
0 ~ 114
0 ~ 127
0,1 (off, on)
0 ~ 114
0 ~ 127
1 ~ 64 ~ 127 (L63 ~ 0 ~ R63)
64
1 ~ 64 ~ 127 (-63 ~ 0 ~ +63)
0 ~ 127
0 ~ 127
0 ~ 12
14 ~ 64 ~ 114 (-50 ~ 0 ~ +50)
14 ~ 64 ~ 114 (-50 ~ 0 ~ +50)
14 ~ 64 ~ 114 (-50 ~ 0 ~ +50)
14 ~ 64 ~ 114 (-50 ~ 0 ~ +50)
0,1 (off, on)
0,1,2 (last, hi, lo)
0,1 (off, on)
0
0,1 (off, on)
0,1 (off, on)
0,1 (off, on)
0,1 (off, on)
0,1 (off, on)
0,1 (off, on)
59